Capitolo 6. Manutenzione ordinaria
IT
6.1. Precauzioni e messa in stato di manutenzione
ATTENZIONE!
•
La manutenzione deve essere affidata esclusivamente a personale esperto conoscitore della
macchina.
•
È vietato fare interventi di manutenzione, lubrificazione, riparazione quando la macchina è in moto e/o
sotto tensione.
•
È vietato effettuare interventi su organi in movimento.
•
Dopo ogni intervento rimontare i ripari eventualmente rimossi, riportando la macchina allo stato
iniziale.
•
Tenere sempre presente tutte le norme di sicurezza elencate nel seguente manuale e quelle stabilite
dalle normative vigenti nel paese di installazione.
PROCEDURA DI MESSA IN STATO DI MANUTENZIONE
La procedura deve essere fatta prima di ogni operazione di manutenzione ordinaria, pulizia e manutenzione
straordinaria; prevede l’isolamento della macchina da tutte le fonti di energia e consiste nel:
•
spegnere la macchina ruotando l’interruttore generale (Q1) in posizione “0” (OFF)
•
togliere la spina dalla presa di rete
•
ASPETTARE 15 minuti per consentire la scarica dei condensatori.
6.2. Tabella di manutenzione
6.2.1. Piano di manutenzione ordinaria
La tipologia della macchina richiede interventi manutentivi ridotti, tuttavia attenersi al Piano di manutenzione.
FREQUENZA
COMPONENTE
TIPO DI OPERAZIONE
Ogni
giorno
Macchina
Rimuovere eventuali residui lasciati dai prodotti in lavorazione e
che potrebbero pregiudicare il corretto funzionamento della
macchina.
Ogni
giorno
Lame
Pulire la superfice che entra in contatto col film utilizzando stracci o
carta.
Non utilizzare oggetti che possano danneggiarne la superficie.
Ogni
12 mesi
Supporti
Effettuare la lubrificazione con grasso tipo NLGI 2.
Ogni
12 mesi
Accoppiamenti
tra ingranaggi
Controllare la presenza di grasso lubrificante.
Ogni
3 mesi
Lame e
barre di contrasto
Controllare lo stato di usura del teflon adesivo e della piattina in
silicone.
AVVERTENZA!
I riduttori sono lubrificati con olio sintetico denominato “lunga vita”, di conseguenza non necessitano di
lubrificazione.
6.2.2. Piano di manutenzione dei dispositivi di sicurezza
È richiesto il controllo periodico dei “
DISPOSITIVI DI SICUREZZA”
elencati in tabella.
FREQUENZA
COMPONENTE
TIPO DI OPERAZIONE
Ogni
mese
Ripari anteriore e
posteriore
Apertura del riparo anteriore e posteriore (in stato di
funzionamento sia manuale che automatico)
Verifica conseguenze:
allarme luminoso e acustico, blocco della macchina.
Ogni
mese
Protezioni
della barra saldante
Spostamento delle protezioni poste attorno alla barra
saldante in corrispondenza dei quattro sensori (in stato di
funzionamento manuale)
Verifica conseguenze:
allarme luminoso e acustico, blocco della macchina.
Ogni
mese
Pulsante di emergenza
Azionamento del pulsante di emergenza (in stato di
funzionamento sia manuale che automatico)
Verifica conseguenze:
allarme luminoso e acustico, blocco della macchina.
Registrazione del controllo
Ogni controllo dei dispositivi di sicurezza deve essere registrato, indicando i dati e l’esito del controllo eseguito:
data della verifica, collaudatore, esito.
Segnalazione di guasto
In caso di rilevazione di guasto, contattare il Servizio Assistenza del Fornitore per l’intervento di ripristino.
28
Summary of Contents for MF21BA54
Page 90: ......