Kapitel 5. Einstellung und Vorbereitung der Maschine
DE
HÖHE SCHWEISSUNG
[mm]
56MPE 56MPS
Dient zur Einstellung der Schweißposition in Hinsicht auf das Band.
Werte: AUTO / MAN.
Wenn auf AUTO eingestellt, erfolgt die Schweißung auf halber Höhe des Produkts.
Ideal für Standardprodukte.
Wenn auf MAN eingestellt, erfolgt die Schweißung nach dem eingestellten Maß (von
der Ebene des Ausgangsbandes aus gemessen). Werte: 0 ÷ 120.
ÖFFNEN SCHWEISSBALKEN
[%]
56MPE 56MPS
Regelt die Öffnung der Schweissbalken. Werte: AUTO / MAN.
Wenn AUTO eingestellt ist, wird das Öffnen der Schweißbalken vom Programm
definiert.
Wenn MAN eingestellt ist, wird das Öffnen vom Benutzer bestimmt (z.B.: um die
Verpackungsgeschwindigkeit zu erhöhen, ist es ausreichend eine Mindestöffnung der
Schweißbalken einzustellen, um die Schließ- und Öffnungszeiten zu vermindern)
Werte: 20 ÷ 100.
AUSWAHL FOTOZELLE
56 56CS 56MPE 56MPS
Die Funktion ermöglicht die Wahl der Fotozelle für die Paketerfassung.
Werte: HORIZ / VERT.
FILTER D. FOTOZELLE
[s]
56 56CS 56MPE 56MPS
Einstellung der Zeit, für die die Fotozelle ein fehlendes Signal ignorieren soll
(empfohlen bei Produkten mit unregelmäßiger Form). Werte: 0 ÷ 1.
Über die nächsten beiden Variablen können die Daten für die manuellen
Einstellungen, die an der Maschine ausgeführt werden müssen, eingegeben werden,
damit jedes Mal, wenn dieses Programm geladen wird, die gespeicherte Einstellung
angewendet werden kann
.
POSITION FOLIENSPANNERRÄDCHEN AN DREIECKEN
56 56CS 56MPE 56MPS
Die Position der Rädchen (R6) (OPTIONAL) mit Bezug auf die metrische Skala (X3)
eingeben (siehe Abschnitt 5.4 PHASE 6).
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist.
AKTIVIERUNG LUFTSTROM
56 56CS 56MPE 56MPS
Angeben, ob für dieses Programm der Bausatz “LUFTSTROM” angewendet wurde
(ON) oder nicht (OFF). Werte: ON / OFF
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist
.
GESCHW. BÄNDER
[%]
56 56CS 56MPE 56MPS
Regelt die Geschwindigkeit des Einlaufbandes (IN) und des Auslaufbandes (OUT) von
6m/min bis 30m/min. Die Bandgeschwindigkeit ist für beide identisch
.
. Werte: 20 ÷
100.
BANDUMKEHR
[mm]
56 56CS 56MPE 56MPS
Kann nur eingestellt werden mit Funktion "PRODUKTLÄNGE" auf MAN. Einstellung
des Abstands zwischen den Produkten. Nach Vorlaufen der Bänder kehrt das
Einlaufband die Laufrichtung um und befördert das Produkt für die eingestellte Distanz
zurück. Werte: 0 ÷ 500.
STOPP SCHWEISSBAND
56 56CS 56MPE 56MPS
Mit dieser Funktion kann das Einlaufband (IN) während des Schweißens angehalten
werden, um die Zusammensetzung der Verpackung zu erleichtern. Werte: ON / OFF.
FOTOZ. LADEBAND
56 56CS 56MPE 56MPS
Falls ON, startet die Maschine im automatischen Zyklus START das Einlaufband nicht;
das Band wird gestartet, wenn die Fotozelle des Ladebandes aktiviert wird.
(OPTIONAL).
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist
.
71
Summary of Contents for MF21BA54
Page 90: ......