Kapitel 5. Einstellung und Vorbereitung der Maschine
DE
FOLIENLOCKERUNG
[mm]
56 56CS 56MPE 56MPS
Einstellung des Folien- und Produktrückzugs in mm vor Ausführung des
Schweißvorgangs (empfohlen bei Produkten mit Höhe über 200 mm). Werte: 0 ÷ 250.
ANNÄHERUNG BANDER
56 56CS
Die Funktion aktiviert das Näherungssystem der Bänder (IN) und (OUT) in der
Schweißzone für den Durchgang kleiner Produkte.
Werte: ON / OFF.
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist.
PERFORIERER
56 56CS 56MPE 56MPS
Diese Funktion aktiviert den pneumatischen Locher (OPTIONAL). Werte: ON / OFF.
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist..
LESEN D. MARKIERUNGEN
56 56CS 56MPE 56MPS
Diese Funktion ermöglicht die Erfassung von auf matter oder farbiger Folie
angebrachten Markierungen durch eine Photozelle (OPTIONAL).
Die Funktion kann nur dann ON sein, wenn sie in den OPTIONALs vorgesehen ist.
VERZOG SP. ABWICKLER
[s]
56 56CS 56MPE 56MPS
Die Funktion ermöglicht die Lockerung der Folienspannung auf den Dreiecken und verzögert
somit den Start des Abwicklers (empfohlen bei Paketen bis 100 mm Höhe). Werte: 0 ÷ 3.
Über die nächsten 3 Variablen können die Daten für die manuellen Einstellungen, die an der
Maschine ausgeführt werden müssen, eingegeben werden, damit jedes Mal, wenn dieses
Programm geladen wird, die gespeicherte Einstellung angewendet werden kann.
ANZ. MIKROPERFORIERER
56 56CS 56MPE 56MPS
Die Anzahl der Mikroperforationsvorrichtungen (MF) eingeben, die an der Maschine
positioniert werden sollen (siehe Abschnitt 5.4 PHASE 6).
POSITION FOLIENSPULE
[mm]
56 56CS 56MPE 56MPS
Die Position der Folienspule mit Bezug auf die metrische Skala (X1) eingeben (siehe
Abschnitt 5.4 PHASE 6).
POSITION UMLENKROLLE FOLIE
[mm]
56 56CS 56MPE 56MPS
Die Position der Umlenkrolle (R5) mit Bezug auf die metrische Skala (X2) eingeben
(siehe Abschnitt 5.4 PHASE 6).
VERZ. AUFWICKLER
[s]
56 56CS 56MPE 56MPS
Die Funktion ermöglicht die Lockerung der Folienspannung auf den Rollen des
Aufwicklers und verzögert somit das Anhalten des Aufwicklers.
Werte: 0 ÷ 1.
Über die nächsten 4 Variablen können die Daten für die manuellen Einstellungen, die am
eventuell zugeordnetem Tunnel ausgeführt werden müssen, eingegeben werden, damit jedes
Mal, wenn dieses Programm geladen wird, die gespeicherte Einstellung angewendet werden
kann.
GESCHWINDIGKEIT
56 56CS 56MPE 56MPS
Die Geschwindigkeit des Förderbandes des Tunnels eingeben.
T. EINGANG
56 56CS 56MPE 56MPS
Die Temperatur der Eingangszone des Tunnels eingeben.
T. AUSGANG
56 56CS 56MPE 56MPS
Die Temperatur der Ausgangszone des Tunnels eingeben.
POSITION DER LEITBLECHE
56 56CS 56MPE 56MPS
Durch Klick auf die Pfeiltasten
▲ und ▼ kann “grafisch” die Position der Leitbleche
des Tunnels dargestellt werden.
Hinweis: Diese Bildschirmseite wechselt je nachdem, ob der Tunnel 50, Tunnel 50 Twin oder
Tunnel 70 zugeordnet sind. Im Tunnel 50 ist die Temperatur einförmig (kein Unterschied
zwischen Eeingangs- und Ausgangszone), statt zwei sind vier Leitbleche vorhanden.
72
Summary of Contents for MF21BA54
Page 90: ......