background image

IMPORTANT NOTICE

• For use with a normal 2-wheel bicycle only. Do not use a tandem, recumbent, or other.

• Use the supplied rear quick release skewer for maximum stability when your bike is 

equipped with a quick release skewer on the rear wheel.
Minoura is not responsible for any problem caused from using your own skewer.

• Hub nut type rear wheel axle is also compatible with VFS150 in standard.

Remove the F-9 Grommet (Hub Nut Protector) from the Right Side Coupling (F-1) for 
better stability.

• Fits wheel size between 24" and 27"/700c. To use 26x1.75" or smaller wheel, install 

the supplied Z-shaped Small Wheel Adaptor.

• Some assembly required. Use correct tools (10mm spanner & M4 hex wrench).

Tools are not supplied in the kit.

• Use on flat and level floor or ground for your safety. Set the trainer on a large enough 

mat or towel to protect the floor and carpet from your sweat and stain.

• Adjust the roller pressure to the rear tire properly in order to maximize your tire life.

Tire and roller contact will eventually wear both your tire and the trainer roller.

• If your trainer is the remote controllable version, check and adjust the remote shifter 

cable tension when you cannot set at L or H even though you turn the shifter lever.

• Touching the spinning wheel and/or any other moving parts while training may cause 

serious injury. Keep children and pets away from the trainer when in use.

• It is not possible to convert the non-remote resistance unit to the remote controllable  

one due to a difference in the inside mechanism.

• If you feel any strange noise, smell or oil leakage, stop using VFS150 immediately and 

contact the retailer where you purchased the VFS150.

• Any warranty will be void if you use VFS150 for other purpose than instructed.

Minorua offers 1-year limited warranty on the resistance unit and 5-year limited 
warranty on the frame from the date of your purchase for any problem caused by 
manufacturer's defect.
Any damage or problem caused by transporting process is not covered under warranty. 
Any damage from shipping or moving must be made to the shipping company.
Read enclosed "Minoura Limited Warranty Policy" card for more detail.

- Page 2 -

Summary of Contents for VFS150









Reviews: