background image

 

 

 

 

IMPORTANT SAFETY INSTRUCTIONS 

 

Operators must read and understand this manual before operating or maintaining this machine. 
Do not operate this machine in areas containing flammable or explosive materials. 
 

This machine is designed solely for scrubbing dirt and dust in an indoor environment. Minuteman does not 
recommend the use of this machine in any other capacity. 
The information provided in this manual will help prevent a potential hazard to the operator and 
equipment. Read this manual carefully and be aware when hazardous conditions can exist. Take necessary 
steps to locate all safety devices on the machine and train the personnel operating the machine. Report any 
machine damage or faulty operation immediately.  

Do not use machine if it is not in proper operating condition.

 

 

FOR SAFETY DURING OPERATION: 

Keep hands and feet clear of moving parts while machine is in operation. 
Make sure all safety devices are in place and operate properly. All covers, doors and latches must be 
closed and fastened before use. 
During operation, attention should be paid to other persons in the work area. 
Electric motors and components can cause an explosion when operated near explosive materials or vapor. 
Do not operate this machine near flammable materials such as solvents, thinners, fuels, grain dust, etc.

  

Store or park this machine on a level surface only, with the key switch in the off position. To prevent 
unauthorized use, machine should be stored with the key removed. 
This machine is designed for level operation only. 

Do not operate on ramps or inclines

.

 

This machine is not suitable for picking up hazardous dusts. 
Use caution when moving this machine into areas that are below freezing temperatures. Any water in the 
tanks or hoses can cause damage to the machine. 
 

FOR SAFETY WHEN SERVICING OR MAINTAINING MACHINE: 

Stop on a level surface and turn off the machine. 
Disconnect the power to the machine by unplugging the large, red terminal below the recovery tank when 
charging batteries or during installation or removal of brushes. 
Avoid moving parts. Do not wear loose jackets, shirts, or sleeves when working on machine. 
Avoid contact with battery acid. Battery acid can cause burns. When working on or around batteries, wear 
protective clothing and safety glasses. Remove metal jewelry. Do not lay tools or metal objects on top of 
batteries. 
Charging batteries generates explosive gasses. 

Do not charge batteries when open flames or sparks are 

present. Do not smoke. 

Make sure the charger is turned off before disconnecting it from the machine. 

Charge the batteries in a well-ventilated area with the battery cover removed completely. 
Do not clean machine with a pressure washer. 
Authorized personnel must perform repairs and maintenance. Use ONLY Minuteman supplied 
replacement parts. 
 

SAVE THESE INSTRUCTIONS 

Summary of Contents for P260BDCE









































Reviews: