background image

19

English

Para Systems Inc. (Para Systems) warrants this equipment, when properly
applied and operated within specified conditions, against faulty materials or
workmanship for a period of three years from the date of purchase.  For equip-
ment sites within the United States and Canada,  this warranty covers repair or
replacement of defective equipment at the discretion of Para Systems.  Repair
will be from the nearest authorized service center.  Replacement parts and
warranty labor will be borne by Para Systems.  For equipment located outside
of the United States and Canada, Para Systems only covers faulty parts.  Para
Systems products repaired or replaced pursuant to this warranty shall be war-
ranted for the unexpired portion of the warranty applying to the original product.
This warranty applies only to the original purchaser who must have properly
registered the product within 10 days of purchase.

The warranty shall be void if (a) the equipment is damaged by the customer, is
improperly used, is subjected to an adverse operating environment, or is oper-
ated outside the limits of its electrical specifications; (b) the equipment is re-
paired or modified by anyone other than Para Systems or Para Systems-ap-
proved personnel; or (c) has been used in a manner contrary to the product’s
User's Manual or other written instructions.

Any technical advice furnished before or after delivery in regard to use or appli-
cation of Para Systems’s equipment is furnished without charge and on the
basis that it represents Para Systems’s best judgment under the circumstances,
but it is used at the recipient’s sole risk.

EXCEPT AS PROVIDED HEREIN, PARA SYSTEMS MAKES NO WARRAN-
TIES, EXPRESSED OR IMPLIED, INCLUDING WARRANTIES OF MERCHANT-
ABILITY AND FITNESS FOR A PARTICULAR PURPOSE.  Some states do not
permit limitation of implied warranties; therefore, the aforesaid limitation(s) may
not apply to the purchaser.

Summary of Contents for PRO1100E

























Reviews: