background image

23

Machine Overview

 © 2015 Minuteman International, Inc.

X17 ECO CFS Carpet Extractor  #988725UMCFS  Rev. C 03/18

• 390070 - Upholstery Tool (Requires Hose Assembly)
• 831255 - Scrub/Vacuum Wand (Requires Hose Assembly)
• 828924 or 830750 -  Hose assemblies for non-motorized tools. 
                                    Does not require QC coupler (Item G)
• 831019 - Pump-Out Hose
• 17603 -  Vac Out Hose

C

B

A

G

D

E

F

 Accessories

• X17115, use C46300-00 - Motorized Tool
• X17230, use C46300-02 - Motorized Tool 

Only these tools may plug into the 

Auxiliary 

Power 

(Fig. 1/B)

• The Vacuum Hose (Ref. Item G, pg 11) must be fi rst disconnected 
from the machine back panel. Connect the Suction Hose (Fig. 2/D) 
tool to the Vacuum Inlet (Fig. 1/A). 
• Connect the accessory Power Cord (Fig. 2/E) to the Auxiliary Power 
(Fig. 1/B). 
• A Coupler-Quick Connect (Fig. 2/G) (p/n: 450295) is required 
to connect the tool Solution Hose (Fig. 2/F) to the quick-connect 
Solution Coupling (Fig. 1/C).
• To turn ON the tool, the auxiliary switch in the machine handle must 
be in the (II) position as shown on pg 12, (Item D).  The vacuum 
switch must also be turned on when using the motorized tool.

Caution! 

Brush motor must be turned OFF when using 

auxiliary function. If the brush motor is ON, damage to carpet 
my occur.

Figure 1

Figure 2

Summary of Contents for X17 ECO CFS





































Reviews: