www.mirabelleproducts.com
11
Care and Cleaning
The use of bath oils and bath salts is not recommended due to the difficulty in cleaning the systems and doing so will
void the consumer's
warranty.
Air and Total Massage Baths are equipped with an Automatic Purge Cycle for the air blower only. The air blower has a pre-programmed
purge cycle built in to expel the remaining water in the air channels. It activates within 20 minutes after the Air Bath is turned off and then
blows for about 2 to 3 minutes.
After the cycle is completed it will shut off automatically. There is nothing to be alarmed about if you hear a blowing noise coming from
the tub after the tub has been turned off. The noise you hear is the cleaning cycle in operation. It is recommended to activate the air bath
routinely to purge water from the air channel when tub is used as a soaker or shower only. Purge cycle is only activated when blower has
been used.
Pump and pipe circulation system should be flushed before first use and on a monthly basis when product is under normal use.
Below are the recommended procedures for cleaning:
DO NOT use powdered cleaners unless cleaner is fully dissolved in water.
DO NOT RUN WHIRLPOOL DRY. Fill the tub with hot water 2-3 inches above the jets and add 2-3 teaspoons of low foaming detergent
such as dish washing machine detergent.
DO NOT use full strength bleach of ammonia cleaning solutions. Chemically active cleaning solution can damage the bath surface.
• Switch on whirlpool and run for 10 minutes.
• Drain tub completely.
• Fill tub with cold water above jets.
• Switch on whirlpool and run for 5 minutes.
• Drain tub completely.
DO NOT USE ABRASIVE CLEANERS as they will scratch and dull the surface of the acrylic and
void the consumer warranty
. Plaster can
be removed using a sharpened wooden stick.
DO NOT USE METAL SCRAPERS, WIRE BRUSHES OR OTHER HARSH ABRASIVE TOOLS.
Usually a mild detergent will remove construction debris. More stubborn debris may be removed with denatured alcohol, or Clorox Soft
Scrub® cleaner. Light scratches and dulled areas may be restored to original luster by rubbing with an automotive type cleaning compound
such as DuPont White Polishing Compound®.
Note: To restore dull or scratched units: Apply white automotive polishing with a clean rage. Rub scratches and dull areas vigorously. Wipe off
residue. Follow with a coat of white automotive paste wax.
DO NOT wax areas where you walk or stand. For crack and major surface damage, call customer service at
1-800-221-3379
for repair
recommendations.
Operating Instructions
1. Fill the bath to at least 3 inches above the jets before activating the pump. DO NOT turn on whirlpool unless jets are completely
submersed in water.
2. The air bath blower and/or whirlpool pump is activated by pushing the control panel buttons (Provincetown and Bradenton system tubs
air/whirlpool is turned on by depressing the actuator button) . DO NOT repeatedly depress the switch in rapid order if you do not see
the whirlpool function right away, as it may take a few seconds before you can see it fully operating. Please see air bath control or Total
Massage Control instructions on the following page for operation and features.
3. If any factory installed fittings are removed; do not operate the unit. A safety hazard may occur.
4. Do not use bubble bath when you operate the whirlpool pump. This might cause excessive foaming.
5. Bath oils should not be used when you operate the whirlpool. If used while soaking, please drain and clean the tub thoroughly prior to
activating the whirlpool system.
6. The use of bath salts is not recommended and doing so will
VOID THE CONSUMER’S WARRANTY
.
7. Both air and whirlpool systems are plumbed in a way that water will drain from the plumbing easily.
8. The air system is designed to purge within 20 minutes after use (see details on previous page).
9. There are no user serviceable parts located under the tub. If a problem develops, call 1-800-221-3379
