Mirabelle GALATIA MIRGA241, Installation Instructions Manual

2

BEFORE INSTALLATION

•  Confirm that there is enough floor space to install the toilet unit and that the bathroom door will open/close 

  without obstruction.

•  Water Pressure. The product is designed to operate with a minimum working pressure of 20psi

.

INSTALLATION PROCEDURES

Step 1: Put the toilet at the appropriate location, mark 

the bolt mounting locations at the rear of the bowl. This 

toilet does not use bolts through the closet flange.

Step 2: Drill holes on the ground at the marked locations 

with a 25/64” (10mm) drill bit. If installing onto concrete 

subfloor, use expansion bolts provided.

Step 3: Confirm that the installation area is clean, 

especially around the toilet mounting location. If 

installing with a closet flange, ensure the top of the 

flange is level with the finished floor for proper seal.

Step 4: Mount the plastic/rubber drain adapter onto the 

outlet on the underside of the bowl. Position the toilet 

squarely to wall and with a rocking motion, press bowl 

down fully to ensure adapter seals into flange. 

Step 5: Alternately tighten bolts until toilet is firmly 

seated on floor.

CAUTION:DO NOT OVERTIGHTEN bOLTS,OR bASE 

MAY BE DAMAGED!

Step 6: Apply clear silicone sealant around the toilet 

edges.

Step 7: Connect the inlet line to the water supply.

12”

(305mm)

8-7/8”

(225mm)

13”

(330mm)

28-3/4” (730mm)

Closet Flange

(optional)

2

BEFORE INSTALLATION

•  Confirm that there is enough floor space to install the toilet unit and that the bathroom door will open/close 

  without obstruction.

•  Water Pressure. The product is designed to operate with a minimum working pressure of 20psi

.

INSTALLATION PROCEDURES

Step 1: Put the toilet at the appropriate location, mark 

the bolt mounting locations at the rear of the bowl. This 

toilet does not use bolts through the closet flange.

Step 2: Drill holes on the ground at the marked locations 

with a 25/64” (10mm) drill bit. If installing onto concrete 

subfloor, use expansion bolts provided.

Step 3: Confirm that the installation area is clean, 

especially around the toilet mounting location. If 

installing with a closet flange, ensure the top of the 

flange is level with the finished floor for proper seal.

Step 4: Mount the plastic/rubber drain adapter onto the 

outlet on the underside of the bowl. Position the toilet 

squarely to wall and with a rocking motion, press bowl 

down fully to ensure adapter seals into flange. 

Step 5: Alternately tighten bolts until toilet is firmly 

seated on floor.

CAUTION:DO NOT OVERTIGHTEN bOLTS,OR bASE 

MAY BE DAMAGED!

Step 6: Apply clear silicone sealant around the toilet 

edges.

Step 7: Connect the inlet line to the water supply.

12”

(305mm)

8-7/8”

(225mm)

13”

(330mm)

28-3/4” (730mm)

Closet Flange

(optional)

2

BEFORE INSTALLATION

•  Confirm that there is enough floor space to install the toilet unit and that the bathroom door will open/close 

  without obstruction.

•  Water Pressure. The product is designed to operate with a minimum working pressure of 20psi

.

INSTALLATION PROCEDURES

Step 1: Put the toilet at the appropriate location, mark 

the bolt mounting locations at the rear of the bowl. This 

toilet does not use bolts through the closet flange.

Step 2: Drill holes on the ground at the marked locations 

with a 25/64” (10mm) drill bit. If installing onto concrete 

subfloor, use expansion bolts provided.

Step 3: Confirm that the installation area is clean, 

especially around the toilet mounting location. If 

installing with a closet flange, ensure the top of the 

flange is level with the finished floor for proper seal.

Step 4: Mount the plastic/rubber drain adapter onto the 

outlet on the underside of the bowl. Position the toilet 

squarely to wall and with a rocking motion, press bowl 

down fully to ensure adapter seals into flange. 

Step 5: Alternately tighten bolts until toilet is firmly 

seated on floor.

CAUTION:DO NOT OVERTIGHTEN bOLTS,OR bASE 

MAY BE DAMAGED!

Step 6: Apply clear silicone sealant around the toilet 

edges.

Step 7: Connect the inlet line to the water supply.

12”

(305mm)

8-7/8”

(225mm)

13”

(330mm)

28-3/4” (730mm)

Closet Flange

(optional)

Note: this toilet is Not compatible with off-set 
closet flaNges