background image

Page 17

• When using the heater after extended periods of storage, re-attach the reflector.

The heater should never be operated without the reflector in place.

• If the heater is to be stored indoors, the gas bottle must be disconnected and left outside. in a dry, 

well-ventilated area,away from any sources of heat or ignition.

• Do not let children tamper with the bottle.

Service

If your heater needs maintenance or is not working properly, please contact your local authorized agent 

for service. It is a necessity to contact an authorized source for replacement of parts and/or servicing. 

This work must be carried out by a qualified gas technician. Spare parts may be obtained by contacting 

our spare parts department by email: info@uigroup.ie

WARNINGS

• NEVER use indoors, in an enclosed area or below ground level.

• This appliance is intended for use with LPG bottled gas only.

• This appliance features a flame failure and tilt device. In the event of a wind blowing the flame out or 

the unit being tipped over, the gas supply will be cut off from the cylinder. In this event, the knobs

should be set to off and you should wait 5 minutes before re-lighting.

• Failure to read and follow these instructions could result in serious injury or damage to property.

• This product will become hot when in use – take care when touching.

• Keep children and pets at a safe distance from the unit when in use.

• DO NOT move this product when in use.

• Any modification of this appliance may be dangerous.

• DO NOT use heater where the reflector is within 40 inches (1m) of any flammable structure or surface.

• NEVER operate the heater with the top half covered (burner head, reflector, etc.)

• DO NOT leave this product unattended when in use.

• Always keep the cylinder level and vertical when positioning inside the base.

• ONLY use this appliance on a flat LEVEL non flammable surface or ground. 

• Positioning, ensure the unit is a minimum of 40 inches (1m) from flammable items or structure from all

sides and above.

• Always leak test the unit before use, annually, or after storage, when parts are replaced/serviced or if

the gas cylinder is removed or replaced.

• When storing the appliance or gas cylinder, ensure they are away from flammable materials or liquids.

• Regularly check that the regulator seal and hose is fitted and that it is in good condition. Replace

parts if necessary.

• Always follow the care and maintenance instructions – regularly maintain your appliance.

• Always replace worn parts – do not use the appliance if a leak, wear, or damage is found.

• DO NOT store or cover the appliance until fully cooled.

• Always shut off the valve at the gas cylinder or the regulator before moving the appliance.

• In the event of high winds particular attention must be taken. Store the unit away or ensure it is at a

safe distance from other items in the event that the unit is blown over.

• Only use with gazebo’s specifically designed to be used with patio heaters.

• Ensure the heater is at a safe distance from glass and PVC doors and windows to stop damage from

any heat build up.

• Read the warnings and instructions use before operation.

Warning: Do not leave the heat focusing reflector of the patio 

heater in the tilt position during rain or windy conditions or 

when the patio heater is not in use or unattended.

Always position the heat focusing reflector in the full down 

position when not in use or during windy or rainy conditions.

DURING RAIN/HIGH WIND CONDITIONS OR WHEN UNATTENDED

Summary of Contents for 200 Btu




















Reviews: