2
A
B
C
D
E
21 533
21 533
42 1067
42 1067
3 76
21 533
18 457
42 1067
36 914
3 76
18 457
17 432
36 914
34 864
3 76
Inch
mm
Inch
mm
Inch
mm
SQD4242
SQD4236
SQD3634
SQD6030
Inch mm
30 762
15 381
60 1524
30 762
3 76
Series of Strada Bases with built in 1’’ Tile Flange on 3 sides
listed in Table 2.
SQD6032
Inch
mm
30 762
16 406
60 1524
32 813
3 76
Position and level the shower base. Fasten the flange of the
base to the wall studs with 5/8" (16mm) or longer screws.
Note:
Remove the protective film from the tile flange before fastening.
Finish the wall as shown in Figure 6.
DRAIN
4”
3”
1"
2"x 4'’
WALL STUD
DRYWALL
SCREW
TILE
SILICONE
CAULKING
TILE FLANGE
FIGURE 6
- WALL FINISHING
FIGURE 7
- FLANGE SCREWS LOCATION
Left,
Back Wall Flange
3 Sided Alcove
Flange, W open
Right,
Back Wall Flange
TESTING
Test the installation after completing the plumbing, but before enclosing
the base and finishing the surroundings. Fill the base with water and
leave it for one hour to ensure that the adjustment of the drain-overflow
assembly is correct, and that there are no leaks.
Mirolin Industries Corp. will not be liable for any kind of damages as a
result of not water testing the unit prior to use by end user.
FINISHING
!
Apply trim around the shower base periphery to finish drywall, if
required.
!
Install Shower Door according to the manufacturer’s instructions if
purchased
Mirolin Industries Corp. is not responsible for any damages incurred as a
result of poor installation of the product.
84 310
17 Sep. 2018
60 Shorncliffe Rd., Toronto, Ontario M8Z 5K1
Telephone: 416.231.9030 Fax: 416.231.0929
www.mirolin.com
Customer Service:
416.231.5790
Canada, U.S.A.: 800.
MIROLIN
(647-6546)
Fax, Canada: 800.463.2236
We want you to be completely satisfied with our products and service. If you have any comments or suggestions, please call
800.MIROLIN(647-6546)
toll free.
Place Assembly -1, the square drain grill with drain nut on the depression
and hold in place. Then fasten drain Assembly - 2 from underneath the
shower base and tighten it.
INSTALLATION CLEAN-UP
Remove construction dirt and residue with a mild liquid detergent. DO NOT USE abrasive cleaners, scouring compounds and pads, metal
scrapers, steel wool, or other materials that could damage or dull the surface of the bath. Remove plaster carefully with a blunt wooden block
having rounded edges. Remove paint and other stubborn stains with isopropyl (rubbing) alcohol.
DO NOT USE products such as acetone (nail polish remover), dry cleaning solution, lacquer thinners, gasoline, pine oil, etc.
MAINTENANCE
The acrylic sheet, which forms the surface of your bathtub, provides one of the most durable surfaces found in modern bathrooms. Keep it bright
and smooth with mild liquid household detergent, soap and water, or foaming cleansers. NEVER USE aromatic solvents, abrasive cleaners,
scouring compounds or pads, strong liquid cleansers, or other material that could damage or dull the surface of the bath.
Restoring Surface Gloss.
- Restore surface gloss by applying a very fine rubbing compound and polishing the surface by hand or with a power
buffer. Finish with an application of a good quality automotive wax.
Minor Repairs to Surface.
- Remove minor scratches and scuffs as follows. First, wet sand the area with 600 grit wet sandpaper until the surface
is smooth. Then, restore the gloss as described under
RESTORING SURFACE GLOSS.
The company reserves the right to change models and specifications without notice.
SQUARE DRAIN ASSEMBLY
DRAIN NUT
RUBBER
GASKET
CARDBOARD
GASKET
DRAIN BODY
Assembly -1
Square grill with drain nut
Assembly - 2
Drain body with gaskets
SQUARE GRILL
STAINLESS STEEL
