background image

HT-5202A/HT-5202G

16

BLADE POSITION

- On the factory all hair clippers are carefully examined to 
ensure that the blades were oiled and aligned.
- The blades of the hair clipper are positioned so that the 
end  of  the  bottom  blade  teeth  is  approximately  1.2mm 
back from the top blade.

BLADE LEVER

• The blade lever is conveniently located near your thumb 
(if you’re right-handed), so it can be easily adjusted while 
the clipper is in your hand. 
• The lever adds versatility to your clipper by allowing you 
to change gradually the length of your hair without using 
an attachment comb. 
• When the lever is in the uppermost position the blades 
will give you the shortest cut and leave your hair very short. 
Pushing  the  lever  downward  will  gradually  increase  the 
hair length.
•  In  its  lowest  position 
the  lever  will  leave  the 
hair  approximately  the 
same  length  as  No.1 
attachment comb. 
•  The  lever  will  also 
extend  the  use  of  the 
blades, since a different 
cutting edge is used in each setting. 
• In addition, if extremely heavy hair cutting has jammed 
the blades, the lever will help you remove the hair that has 
become wedged between two blades without removing the 
blades. 
• While the clipper is running, rapidly move the lever up 
and  down  a  couple  of  times.  Doing  this  each  time  after 
you have finished using your clipper, will help to keep the 
blades clear of cut hair. If your clipper stops cutting and 
this does not help, your cutting blades are blunt. Replace 
them with new ones.

INSTRUCTIONS FOR HAIR CUTTING

1. Before starting the hair cut examine the clipper. Make 
sure that there is no oil between the cutting blade teeth. 
Turn the unit on to have the oil distributed and make sure 
it is running smoothly. Wipe off any excessive oil. It should 

USE

be done after each use. While using the unit, untwist the 
cord from time to time to avoid tangling.
2.  Seat  the  person  so  that  the  person’s  head  is 
approximately  at  your  eye  level.  It  allows  to  ease  the 
visibility, and to control the unit while cutting.
3. Before you start cutting, always comb the hair first to 
make it tangle free and look naturally.
4. Place a towel around the neck and the shoulders of the 
person having the haircut.

RECOMMENDATIONS

• Cut the hair in a relaxed and slow manner. Use only short 
strokes to work gradually over the entire head.
• Always take off a little hair at a time. You can always trim 
off additional hair later.
• As you work, comb the hair frequently and set the hair 
into the style to which you are cutting.
• When cutting with this hair clipper, it is recommended 
to leave the hair dry, not wet. With the hair dry, it is much 
easier to control the amount of hair being cut.

BEGINNING THE HAIRCUT

Cutting hair requires practice, so it is always better to leave 
the hair longer for the first few haircuts, until you become 
used to the length, to which each attachment comb cuts 
the hair.

ATTACHMENT COMBS (see Accessories)

- Attachment Comb No. 1 leaves 3mm hair length.
- Attachment Comb No. 2 leaves 6mm hair length.
- Attachment Comb No. 3 leaves 9mm hair length.
- Attachment Comb No. 4 leaves 12mm hair length.
* right comb is for better hair cutting at the right side.
* left comb is for better hair cutting at the left side. 
Each  comb  attachment  is  marked  accordingly  on  its 
outside middle surface.
- To attach a comb, hold it with the teeth up, and slide it 
onto and along the clipper blade, until the front of the comb 
firmly rests on the clipper blade.
- To remove the comb, simply pull the comb upward and 
away from the clipper blade.
-  For  even  cutting,  allow  the  attachment  comb/the  blade 
to  cut  through  the  hair.  Do  not  force  it  through.  Also 
remember to comb the hair frequently to remove trimmed 
hair and to check for uneven strands.

Summary of Contents for HT- 5202A







































Reviews: