background image

1-888-750-1698

STAPLE YOUR RECEIPT HERE

TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE RELATED QUESTIONS, please call:   

 

 

Venting Services (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as 
“you” or “your”) of range hoods (the “Products”) that such Products will be free from defects in materials or workmanship 
as follows:

One Year Limited Warranty for Parts:

  For one year from the date of your original purchase of the Products, we will 

provide, free of charge, Products or parts to replace those that failed due to manufacturing defects.  We may choose, in 
our sole discretion, to repair or replace parts before we elect to replace the Products.

One Year Limited Warranty for Labor:

  For one year from the date of your original purchase of the Products, we will 

provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to 
manufacturing defects.  After the first year from the date of your original purchase, you are responsible for all labor costs 
associated with this warranty.

Warranty Exclusions: 

 This warranty covers only repair or replacement, at our option, of defective Products or parts 

and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and 
service required for the Products and consumable parts such as light bulbs, metal and carbon filters and fuses; (b) any 
Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installa-
tion contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commer-
cial use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Prod-
ucts or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner 
products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach 
you how to use the Products; or (g) damage to the Products caused by accident, fire, floods or act of God.  If you are 
outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service 
locations and for the travel cost to have a service technician come to your home to repair, remove or reinstall the Prod-
ucts.  After the first year from the date of your original purchase, you are also responsible for all labor costs associated 
with this warranty.  

Limitations of Warranty.  OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE 
AND EXCLUSIVE REMEDY UNDER THIS WARRANTY.  WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSE-
QUENTIAL OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF 
THE PRODUCTS.  THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND IN LIEU OF 
ALL OTHER EXPRESS WARRANTIES.  WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRAN-
TIES  FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING 
THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.

   Some states or provinces do not 

allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential dam-
ages, so the above limitations or exclusions may not apply to you.  To the extent that applicable law prohibits the exclu-
sion of implied warranties, the duration of any applicable implied warranty is limited to the same one-year period 
described above.  Any oral or written description of the Products is for the sole purpose of identifying the Products and 
shall not be construed as an express warranty.  Prior to using, implementing or permitting use of the Products, you shall 
determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in 
connection with such determination.   We reserve the right to use functionally equivalent refurbished or reconditioned 
parts or Products as warranty replacements or as part of warranty service.  This warranty is not transferable from the 
original purchaser and applies in the United States and Canada.

To Obtain Service Under Limited Warranty:  

To qualify for warranty service, you must: (a) notify us at the address or 

telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and part identifi-
cation number and serial number; and (c) describe the nature of any defect in the Product or part.  At the time of the 
request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase 
date.  If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documenta-
tion to obtain service, you will be responsible for all shipping, travel, labor and other costs related to the services.

Venting Services PO Box 6188 Oakland, CA 94603 | 1-888-750-1698 | vsupport@ventingservices.com

Limited Warranty

MAY10.0101

Proof of the original purchase 

date is needed to obtain     

service under warranty

Summary of Contents for MH70130AS






















Reviews: