background image

Line and Trunk Options

8380-383-115-BA

41

Issue 1, February 1999

8. 4. 103 - On-hook Time

An on-hook is determined by the absence of loop current on the line from the Exchange, for 
the specified amount of time.

8. 5. 105 - Time Between Trunk Release and Next Attempt to Connect

This option controls the length of time that the Dialer will remain on-hook (in the idle state) 
prior to going back off-hook and re-dialling when it performs a drop and reseize.

8. 6. 106 - Flash Generation Timer

The Flash Generation Timer governs the duration of time that the Access Control Sequence 
token 

09 will flash the PABX or Centrex line, upon the execution of the token.

Register

Default

Description

103 T

2

T = 0 for 150 ms                     6 for 460 ms
T = 1 for 260 ms                     7 for 500 ms
T = 2 for 300 ms                     8 for 700 ms
T = 3 for 340 ms                     9 for 1100 ms
T = 4 for 380 ms                     

 for 1300 ms

T = 5 for 420 ms                     # for 2500 ms

Register

Default

Description

105 T

0

T = 0 for 5.5 seconds              5 for 8.0 seconds
T = 1 for 6.0 seconds              6 for 8.5 seconds
T = 2 for 6.5 seconds              7 for 9.0 seconds
T = 3 for 7.0 seconds              8 for 9.5 seconds
T = 4 for 7.5 seconds              9 for 10 seconds

Register

Default

Description

106 T

5

T = 0 for 200 ms                     6 for 1400 ms
T = 1 for 400 ms                     7 for 1600 ms
T = 2 for 600 ms                     8 for 1800 ms
T = 3 for 800 ms                     9 for 2000 ms
T = 4 for 1000 ms                   

 for 2300 ms

T = 5 for 1200 ms                   # for 2500 ms

Summary of Contents for SmarT-1 50000241



























































































Reviews: