8
GB
4. Installing BC controller
4.1. Installing BC controllers
Installing hanging bolts
Install locally procured hanging bolts (threaded rod) following the procedure
JLYHQLQWKH¿JXUH7KHKDQJLQJEROWVL]HLV¡PP>LQ@0VFUHZ
To hang the unit, use a lifting machine to lift and pass it through the hanging
bolts.
Suspension bracket has an oval hole. Use a large diameter washer.
[Fig. 4.1.1]
(Unit: mm [in])
A
B
A
14
[9/16]
30
[1-3/16]
Hanging method
<Top view>
A
+DQJLQJEROW¡>@¿HOGVXSSOLHG
B
:DVKHU¿HOGVXSSOLHG
A: Min.30 [1-3/16]
5. Connecting refrigerant pipes and drain pipes
5.1. Pipe connecting method
Brazing
Caution:
.HHSWKHÀDPHRXWRIFRQWDFWZLWKWKHFDEOHVDQGPHWDOVKHHWZKHQEUD]LQJWKHSLSHV
- Failure to do so may result in burnout or malfunction.
When connecting pipes, satisfy the minimum insertion depth requirement for copper pipe joint, and the gap between the pipe outer wall and the joint inner wall as follows.
(Unit: mm)
B
D
A
Pipe size (D)
Minimum insertion depth (B)
Gap (A–D)
5 or more, less than 8
6
0.05 to 0.35
8 or more, less than 12
7
12 or more, less than 16
8
0.05 to 0.45
16 or more, less than 25
10
25 or more, less than 35
12
0.05 to 0.55
35 or more, less than 45
14
6LOYHUEUD]HWKHSLSHVLQFRUURVLYHHQYLURQPHQWVVXFKDVLQZKLFKWKHFRQFHQWUDWLRQRIVXOSKXURXVDFLGJDVLVKLJK
'RQRWXVHDORZWHPSHUDWXUHEUD]LQJPDWHULDODVLWLVQRWVWURQJHQRXJK
:KHQUHEUD]LQJWKHFRQQHFWLRQVXVHWKHVDPHEUD]LQJPDWHULDO
3DLQWWKHEUD]HGVHFWLRQVDIWHUEUD]LQJ
8VHWKHSURSHUÀX[EDVHGRQWKHEDVHPDWHULDOW\SHVKDSHEUD]LQJW\SHDQGEUD]LQJPHWKRG
Procedures
(1)
%UD]HWKHSLSHVDVVKRZQLQWKH¿JXUHEHORZDWWKHWHPSHUDWXUHDSSURSULDWHIRUWKHEUD]LQJPDWHULDO
$IWHUEUD]LQJNHHSVXSSO\LQJDÀRZRIQLWURJHQJDVXQWLOWKHSLSHVEHFRPHFRROHQRXJKWREHWRXFKHGE\KDQG%HFDUHIXOQRWWREXUQ\RXUVHOI
(2)
&RPSOHWHO\UHPRYHWKHÀX[DIWHUEUD]LQJ
(After brazing, keep supplying a
ÀRZ RI QLWURJHQ JDV XQWLO WKH EUD]HG
section is cooled down to 200ºC or
lower.)
N
2
Cylinder
Stuff something in the pipe to keep air from enter-
ing the pipe.
Brazed section
6XSSO\ D ÀRZ RI GU\ QLWURJHQ JDV DW WKH UDWH
\RXVOLJKWO\IHHOWKHÀRZDERXWOLWHUPLQXWH
Example of brazing pipes under nitrogen purge
Notes:
Keep the heated area to a minimum and braze the pipes at the appropriate temperature.
7RSUHYHQWD¿UHFRYHUWKHSLSHVZLWKDPHWDOVKHHWDQGSODFHDZHWWRZHORQWKHSLSHV
After brazing pipes, do not splash water on the pipes to cool them down.
$YRLGJLYLQJPHFKDQLFDOVKRFNWRWKHSLSHVXQWLOWKHEUD]HGVHFWLRQVKDYHVROLGL¿HG
Make sure to check the components of the antioxidant before use. The components must not corrode the pipes if mixed with the refrigerant or refrigerant
oil.
X
Be sure to install the BC controllers level. Installing obliquely may
cause a risk of drain leakage. Use a level to check the unit’s level. If it
LVREOLTXHORRVHQWKH¿[LQJQXWDQGPDNHDQDGMXVWPHQW
Caution:
Be sure to install the unit body level.
