Mitsubishi Electric City Multi PLFY-P15VCM-E3 Technical & Service Manual Download

Page: 30 / 32

OPERATING PROCEDURE

PHOTOS & ILLUSTRATIONS

7. Removing the pipe temperature detection/liquid (TH22)

and pipe temperature detection/gas (TH23)

(1) Remove the panel. (Refer to procedure

)

(2) Remove the drain pan. (Refer to procedure

)

(3) Disconnect the pipe temperature detection/liquid or the pipe

temperature detection/gas from the holder.

(4) Remove the 3 screws fixed to the piping cover, and remove

the piping cover. (See Photo 9)

(5) Remove the 2 screws fixed to the control box cover, and

remove the control box cover.

Pipe temperature detection/liquid (TH22)

(6) Remove the connector (CN21) from the indoor controller

board, and disconnect the pipe temperature detection/liquid.

Pipe temperature detection/gas (TH23)

(6) Remove the connector (CN29) from the indoor controller

board, and disconnect the pipe temperature detection/gas

with its holder.

8. Removing the fan motor (MF)

(1) Remove the panel. (Refer to procedure 3)

(2) Remove the drain pan. (Refer to procedure 6)

(3) Remove the nut and the washer from the turbo fan, and

remove the turbo fan.

(4) Remove the 2 screws fixed to the control box cover, and

remove the control box cover.

(5) Disconnect the connector of the FAN from the indoor con

troller board.

(6) Remove the 3 screws fixed to the piping cover, and remove

the piping cover. (See Photo 9)

(7) Remove the 6 screws fixed to the flat plate, and remove

the flat plate.

(8) Disconnect the lead wires to the direction of the fan motor,

and remove the 3 nuts of the fan motor.

Photo 5

6. Removing the drain pan

(1) Remove the panel. (Refer to procedure 3)

(2) Remove the room temperature detection and the 2 lead

wires held with fastener; wireless controller board relay

connector (9P red) and panel relay connector (10P white).

(3) Remove the 4 screws fixed to the drain pan, and remove

the drain pan.

(4) Remove the fan guard. (Refer to procedure 2)

Photo 4

Control box

Thermistor

(Pipe temperature

detection/ Liquid)

(TH22)

Screw

Room

temperature

detection

(TH21)

Drain pan

Control box

Photo 6

5. Removing the room temperature detection (TH21)

(1) Remove the panel. (Refer to procedure 3)

(2) Pull out the room temperature detection from the drain pan.

(3) Remove the 2 screws fixed to the control box cover, and

remove the control box cover.

(4) Remove the connector (CN20) from the indoor controller

board, and disconnect the room temperature detection.

Fan guard

Drain plug

Connectors

Thermistor

(Pipe temperature

detection/ Gas)

(TH23)

LEV

Fan motor

(MF)

Nut

Flat plate

Screws

Nut

Lead

wires

Nut

Screw

Screws

OCH569

Summary of Contents for City Multi PLFY-P15VCM-E3

































Search results

Summary of Contents for City Multi PLFY-P15VCM-E3

Reviews:

Related manuals for City Multi PLFY-P15VCM-E3

Brands by name

Popular brands

Mitsubishi Electric City Multi PLFY-P15VCM-E3, Technical & Service Manual

Search results

Summary of Contents for City Multi PLFY-P15VCM-E3

Reviews:

Related manuals for City Multi PLFY-P15VCM-E3

Brands by name

Popular brands