Mitsubishi Electric DX-TL900U Installation And Operation Manual Download

Page: 72 / 76

•••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••••

■

Warnings and their appropriate countermeasures

#1 Options in the CALL OUT options column:
• Selectable : CALL OUT output can be selected/de-selected on the menu.
• Fixed

: a CALL OUT signal is emitted without prior selection of this function using the menu.

• None

: no CALL OUT signal is emitted, but a warning indicator will appear on screen.

CALL OUT signal output can be stopped by pressing the WARNING RESET button.

Warning Display

CALL OUT

output

page

Canceling

the warning

Code

Status

Countermeasure

REC/FULL

COPY/FULL
REST/FULL

REC/REM

COPY/SIZE/DATA ERROR
REST/SIZE/DATA ERROR

COPY/MEDIA ERROR
REST/MEDIA ERROR

COPY/NO MEDIA
REST/NO MEDIA

NON SIGNAL

(The warning will
indicate the number
of the non-functioning
camera. )

IMAGE MODIFIED

SYSTEM ERROR
PLAY/SYSTEM ERROR
REC/SYSTEM ERROR
COPY/SYSTEM ERROR
REST/SYSTEM ERROR
REC/RW
COPY/RW
REST/RW
<DEVICE ERROR>

TEMP

MIRROR

FAN

WNG1100

WNG3100
WNG4100

WNG1200

WNG3701
WNG4701

WNG3702
WNG4702

WNG3703
WNG4703

WNG5400

WNG5500

WNG5100
WNG24 #2
WNG14 #2
WNG34 #2
WNG44 #2
WNG13 #2
WNG33 #2
WNG43 #2
WNG62 #2

WNG5200

WNG61 #2

WNG5300

43, 46

46, 47

15, 62

21, 22,
38

Selectable

None

Selectable

None

Fixed

Fixed when
setting is
“ON”
Fixed

None

Selectable

• HDD recording capacity is
empty.

• Media recording capacity is
empty.

• The remaining HDD capacity
has reached the value set in
HDD REMAIN.
• The data that is being copied/
restored exceeds the capacity of
the recording device, or there is
no original data.
• Error has occurred in the
Compact Flash Card.

• No Compact Flash Card has
been inserted.

Video signal was lost for more
than 5 seconds during recording.

Video data that has been altered
was played back.

System error has occurred.

Error has occurred during
reading/writing of data to
HDD/media.
Unable to recognize HDD

Issued when in a high
temperature environment within
the tolerance level.

One HDD could not be detected
during mirroring.

The fan stopped.

• When the warning is cancelled,
the unit will start over-writing
the oldest data remaining in the
hard disk drive.
• Archive or copy data as
necessary.
• Replace with new media.
• Replace media if necessary.

• Copy data as necessary.

• Set the copy/restore range
again.
• Replace the new media.

• Check the Card.
(Insert the media if there
is none.)
• Insert the Card.

• Check whether the unit and
camera are properly connected,
and that electricity is on.
• Check whether the visual signal
is being properly outputted.
• Check to see if there is a
camera set for operation with
no video signal input.

• Reboot.
• Check the HDD/media.

• Check the HDD/media.

• Reboot.

• Turn off the power and change
the installation condition.

• Reboot.

• Turn off the power and stop
usage.
• Request for repair.

Press the
WARNING
RESET button.

Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.

Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Stop recording.

Output video
signals.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.

Press the
WARNING
RESET button.
Turn off the
power
Press the
WARNING
RESET button.
Lower
the temperature.
Press the
WARNING
RESET button.
Press the
WARNING
RESET button.
Rotate the fan.

#2 : 0 0 : MASTER
0 1 : SLAVE
1 1 : CFC

Warnings and CALL OUT output