Mitsubishi Electric GT2103-PMBD Manual Download

Page: 1 / 6

This manual confers no industrial property rights or any rights of any other

kind, nor does it confer any patent licenses. Mitsubishi Electric Corporation

cannot be held responsible for any problems involving industrial property rights

which may occur as a result of using the contents noted in this manual.

Warranty

Exclusion of loss in opportunity and secondary loss from warranty liability

Regardless of the gratis warranty term, Mitsubishi shall not be liable for

compensation to:

(1) Damages caused by any cause found not to be the responsibility of

Mitsubishi.

(2) Loss in opportunity, lost profits incurred to the user by Failures of Mitsubishi

products.

(3) Special damages and secondary damages whether foreseeable or not,

compensation for accidents, and compensation for damages to products

other than Mitsubishi products.

(4) Replacement by the user, maintenance of on-site equipment, start-up test run

and other tasks.

For safe use

This product has been manufactured as a general-purpose part for general
industries, and has not been designed or manufactured to be incorporated in
a device or system used in purposes related to human life.
Before using the product for special purposes such as nuclear power, electric
power, aerospace, medicine or passenger movement vehicles, consult with
Mitsubishi Electric.
This product has been manufactured under strict quality control. However
when installing the product where major accidents or losses could occur if the
product fails, install appropriate backup or failsafe functions in the system.



HEAD OFFICE : TOKYO BUILDING, 2-7-3 MARUNOUCHI, CHIYODA-KU, TOKYO 100-8310, JAPAN

Side

ENGLISH

CHINESE

JY997D61901C

Side

Safety Precaution

(Read these precautions before using.)

Before using this product, please read this manual and the relevant manuals

introduced in this manual carefully and pay full attention to safety to handle the

product correctly.

The precautions given in this manual are concerned with this product.

In this manual, the safety precautions are ranked as "WARNING" and

"CAUTION".

Depending on circumstances, procedures indicated by "CAUTION" may also be

linked to serious results. In any case, it is important to follow the directions for

usage

Indicates that incorrect handling may cause hazardous

conditions, resulting in death or severe injury.

Indicates that incorrect handling may cause hazardous

conditions, resulting in medium or slight personal injury

or physical damage.

DESIGN PRECAUTIONS



Some failures of the GOT or cable may keep the outputs on or off. Some

failures of a touch panel may cause malfunction of the input objects such as a

touch switch. An external monitoring circuit should be provided to check for

output signals which may lead to a serious accident. Not doing so can cause

an accident due to false output or malfunction.



Do not use the GOT as the warning device that may cause a serious

accident. An independent and redundant hardware or mechanical interlock is

required to configure the device that displays and outputs serious warning.

Not doing so can cause an accident due to false output or malfunction.



When the GOT detects its backlight failure, the GOT disables the input

operation on the touch switch(s). Thus, operators cannot operate the GOT

with touches. The GOT backlight failure can be checked with a system signal

of the GOT.



Even when the display section has dimmed due to a failure of the liquid

crystal section or the backlight on the GOT, the input operation of the touch

switches may still be enabled. This may cause an incorrect operation of the

touch switches. For example, if an operator assumes that the display section

has dimmed because of the screen save function and touches the display

section to cancel the screen save, a touch switch may be activated. h

touches. The GOT backlight failure can be checked with a system signal of

the GOT.



The display section of the GOT is an analog-resistive type touch panel.

Simultaneous pressing of two or more areas on the display section may

activate the switch between those areas. Do not press two or more areas

simultaneously on the display section. Doing so may cause an accident due

to incorrect output or malfunction.



When programs or parameters of the controller (such as a PLC) that is

monitored by the GOT are changed, be sure to shut off the power of the GOT

promptly and power on the GOT again. Not doing so can cause an accident

due to false output or malfunction.



If a communication fault (including cable disconnection) occurs during

monitoring on the GOT, communication between the GOT and PLC CPU is

suspended and the GOT becomes inoperative. A system where the GOT is

used should be configured to perform any significant operation to the system

by using the switches of a device other than the GOT on the assumption that

a GOT communication fault will occur. Not doing so can cause an accident

due to false output or malfunction.

DESIGN PRECAUTIONS



When the security of the GOT and relevant information need to be protected

against illegal access from an external device via the Internet, take measures at

the user's discretion.

Failure to do so may cause the configured information to be read out illegally.

DESIGN PRECAUTIONS



Do not bundle the control and communication cables with main-circuit, power or

other wiring. Run the above cables separately from such wiring and keep them a

minimum of 100 mm apart. Not doing so noise can cause a malfunction.



Do not press the GOT display section with a pointed material as a pen or driver.

Doing so can result in a damage or failure of the display section.



When the GOT is connected to the Ethernet network, the available IP address is

restricted according to the system configuration.

- When multiple GOTs are connected to the Ethernet network: Do not set the IP

address (192.168.3.18) for the GOTs and the controllers in the network.

- When a single GOT is connected to the Ethernet network: Do not set the IP

address (192.168.3.18) for the controllers except the GOT in the network.

Doing so can cause the IP address duplication. The duplication can negatively

affect the communication of the device with the IP address (192.168.3.18). The

operation at the IP address duplication depends on the devices and the

system.



Turn on the controllers and the network devices to be ready for communication

before they communicate with the GOT. Failure to do so can cause a

communication error on the GOT.



When the GOT is subject to shock or vibration, or some colors appear on the

screen of the GOT, the screen of the GOT might flicker.

MOUNTING PRECAUTIONS



Be sure to shut off all phases of the external power supply used by the system

before mounting or removing the GOT main unit to/from the panel. Not doing so

can cause the unit to fail or malfunction.

MOUNTING PRECAUTIONS



Use the GOT in the environment that satisfies the general specifications

described in this manual. Not doing so can cause an electric shock, fire,

malfunction or product damage or deterioration.



When mounting the GOT to the control panel, tighten the mounting screws in the

specified torque range (0.20 N·m to 0.25 N·m) with a Phillips-head screwdriver

No.2. Undertightening can cause the GOT to drop, short circuit or malfunction.

Overtightening can cause a drop, short circuit or malfunction due to the damage

of the screws or the GOT.



When mounting the SD card unit to the GOT, mount it on the side of the GOT, and

tighten the tapping screws in the specified torque range (0.3 N·m to 0.6 N·m) with

a Phillips-head screwdriver No. 2.



Remove the protective film of the GOT. When the user continues using the GOT

with the protective film, the film may not be removed.



Operate and store the GOT in environments without direct sunlight, high

temperature, dust, humidity, and vibrations.



Do not use the GOT in an environment with oil or chemicals. Doing so may cause

failure or malfunction due to the oil or chemical entering into the GOT.

WIRING PRECAUTIONS



Be sure to shut off all phases of the external power supply used by the system

before wiring. Failure to do so may result in an electric shock, product damage or

malfunctions.

WIRING PRECAUTIONS



Please make sure to ground FG terminal of the GOT power supply section by

applying 100

Ω

or less which is used exclusively for the GOT. Not doing so may

cause an electric shock or malfunction.



Correctly wire the GOT power supply section after confirming the rated voltage

and terminal arrangement of the product. Not doing so can cause a fire or failure.



Tighten the terminal screws of the GOT power supply section in the specified

torque range (0.22 N·m to 0.25 N·m). Undertightening can cause a short circuit or

malfunction. Overtightening can cause a short circuit or malfunction due to the

damage of the screws or the GOT.



Exercise care to avoid foreign matter such as chips and wire offcuts entering the

GOT. Not doing so can cause a fire, failure or malfunction.



Plug the communication cable into the GOT interface or the connector of the

connected unit, and tighten the mounting screws and the terminal screws in the

specified torque range. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction dueto the damage of the

screws or unit.

Certification of UL, cUL standards



Using GOT

GOT is for use on a Flat Surface of a Type 1 Enclosure.

Notification of CE marking

The following products have shown compliance through direct testing (to the
identified standards) and design analysis (forming a technical construction file) to the
European Directive for Electromagnetic Compatibility (2004/108/EC) when used as
directed by the appropriate documentation.



This product is designed for use in industrial applications

- Type: Graphic Operation Terminal
- Models: GOT series

For more details please contact your local Mitsubishi Electric sales site.
For details of CE marking, refer to the following.



GOT2000 series User's Manual

Manual

The following shows manuals relevant to this product.

Detailed Manual

For detailed manuals, refer to the PDF manuals stored in the DVD-ROM for the
drawing software used.

Relevant Manuals

For relevant manuals, refer to the Help or the PDF manuals stored in the DVD-ROM
for the drawing software used.
The latest manuals are also available from MITSUBISHI ELECTRIC FA Global
Website (http://www.MitsubishiElectric.co.jp/fa).

Before using the GOT

Connect the connector of the GOT to the connector of the battery.
Refer to the GOT2000 Series User’s Manual (Hardware) for the connection
instructions.
For details on the GOT specifications, installing instructions, wiring, maintenance
and inspection, or checking procedure for the version and the compatible standard,
refer to the GOT2000 Series User’s Manual (Hardware).

Bundled Items

TEST OPERATION
PRECAUTIONS



Before performing the test operations of the user creation monitor screen (such

as turning ON or OFF bit device, changing the word device current value,

changing the settings or current values of the timer or counter, and changing the

buffer memory current value), read through the manual carefully and make

yourself familiar with the operation method. During test operation, never change

the data of the devices which are used to perform significant operation for the

system. False output or malfunction can cause an accident.

STARTUP/MAINTENANCE
PRECAUTIONS



When power is on, do not touch the terminals. Doing so can cause an electric

shock or malfunction.



Before starting cleaning or terminal screw retightening, always switch off the

power externally in all phases. Not doing so can cause the unit to fail or

malfunction. Undertightening can cause a short circuit or malfunction.

Overtightening can cause a short circuit or malfunction due to the damage of the

screws or unit.

STARTUP/MAINTENANCE
PRECAUTIONS



Do not disassemble or modify the unit. Doing so can cause a failure,

malfunction, injury or fire.



Do not touch the conductive and electronic parts of the unit directly. Doing so

can cause a unit malfunction or failure.



The cables connected to the unit must be run in ducts or clamped. Not doing so

can cause the unit or cable to be damaged due to the dangling, motion or

accidental pulling of the cables or can cause a malfunction due to a cable

connection fault.



When unplugging the cable connected to the unit, do not hold and pull from the

cable portion. Doing so can cause the unit or cable to be damaged or can cause

a malfunction due to a cable connection fault.



Do not drop the module or subject it to strong shock. A module damage may

result.



Before touching the unit, always touch grounded metals, etc. to discharge static

electricity from human body, etc. Not doing so can cause the unit to fail or

malfunction.

TOUCH PANEL
PRECAUTIONS



For the analog-resistive film type touch panels, normally the adjustment is not

required. However, the difference between a touched position and the object

position may occur as the period of use elapses. When any difference between

a touched position and the object position occurs, execute the touch panel

calibration.



When any difference between a touched position and the object position occurs,

other object may be activated. This may cause an unexpected operation due to

incorrect output or malfunction.

PRECAUTIONS WHEN THE
DATA STORAGE IS IN USE



If the SD card mounted on drive A of the GOT is removed while the GOT is

accessed, processing for the GOT might be interrupted about for 20 seconds.

The GOT cannot be operated during this period. The functions that run in the

background including a screen updating, alarm, logging, scripts, and others are

also interrupted. Since this interruption makes an impact to the system

operation, it might cause failure. After inhibiting access to the SD card on the

GOT utility screen, check that the SD card access LED is off and remove the SD

card.

PRECAUTIONS WHEN THE
DATA STORAGE IS IN USE



If the data storage mounted on the GOT is removed while the GOT is accessed,

the data storage and files are damaged. To remove the data storage from the

GOT, check that the access to the data storage in SD card access LED, the

system signal, and others is not performed.



When removing the SD card from the GOT, make sure to support the SD card

by hand as it may pop out. Failure to do so may cause the SD card to drop from

the GOT, resulting in a failure or break.



Before removing the SD card from the GOT, follow the procedure for removal on

the utility screen of the GOT. After the successful completion dialog is displayed,

remove the SD card by hand carefully. Failure to do so may cause the SD card

to drop from the GOT, resulting in a failure or break.

DISPOSAL PRECAUTIONS



When disposing of this product, treat it as industrial waste.

TRANSPORTATION
PRECAUTIONS



Make sure to transport the GOT main unit and/or relevant unit(s) in the manner

they will not be exposed to the impact exceeding the impact resistance

described in the general specifications of this manual, as they are precision

devices. Failure to do so may cause the unit to fail. Check if the unit operates

correctly after transportation.



When fumigants that contain halogen materials such as fluorine, chlorine,

bromine, and iodine are used for disinfecting and protecting wooden packaging

from insects, they cause malfunction when entering our products. Please take

necessary precautions to ensure that remaining materials from fumigant do not

enter our products, or treat packaging with methods other than fumigation (heat

method). Additionally, disinfect and protect wood from insects before packing

products.

Standard

Remark

EN61131-2 : 2007

Programmable

controllers - Equipment,

requirements and tests

EMI

Compliance with all relevant aspects of the

standard. (Radiated Emissions)

EMS

Compliance with all relevant aspects of the

standard.

(ESD, RF electromagnetic field, EFTB, Surge,

R F c o n d u c t e d d i s t u r b a n c e s a n d P o w e r

frequency magnetic field)

Manual name

Manual number

(Model code)

GOT2000 Series User’s Manual (Hardware) SH-081194ENG-A (1D7MJ5)

GOT2000 Series User’s Manual (Utility)

SH-081195ENG-A (1D7MJ6)

Model name

Remark

GT2103-PMBD/PMBDS/PMBDS2/PMBLS

GOT main unit

(The maintenance supplies below

are packed with the product.)

Model name

Remark

PLC Communication Connector

Panel Mounting Bracket (with M4 × 20 screws)

Panel Mounting Packing

GT21 General Description (This manual)

1. GOT series User's Manual Specifications

1.1 General Specifications

*1 The operating ambient temperature indicates the temperature inside the enclosure of the control panel to which the GOT is installed.
*2 If the ambient temperature exceeds 40°C, the absolute humidity must not exceed 90% at 40°C.
*3 Do not use or store the GOT under pressure higher than the atmospheric pressure of altitude 0 m. Doing so may cause a malfunction. When an air purge is made inside

the control panel by adding pressure, there may be a clearance between the surface sheet and the screen, making you difficult to use the touch panel, or the sheet may

come off.

*4 This indicates the section of the power supply to which the equipment is assumed to be connected between the public electrical power distribution network and the

machinery within the premises. Category II applies to equipment for which electrical power is supplied from fixed facilities. The withstand surge voltage for the equipment

with the rated voltage up to 300 V is 2500 V.

*5 This indicates the occurrence rate of conductive material in an environment where a device is used. Pollution degree 2 indicates an environment where only non-

conductive pollution occurs normally and a temporary conductivity caused by condensation shall be expected depending on the conditions.

*6 Except 5 V power supply type.

1.2 Performance Specifications

Item

Specifications

Operating ambient temperature

0 to 55°C (When mounted horizontally), 0 to 50°C (When mounted vertically)

Storage ambient temperature

-20 to 60



Operating ambient humidity

10% RH to 90% RH, non-condensing

Storage ambient humidity

10% RH to 90% RH, non-condensing

Vibration resistance

Compliant with

JIS B3502

and IEC61131-2

Frequency

Acceleration

Half amplitude

Sweep Count

Under intermittent

vibration

5 to 8.4 Hz

3.5 mm

10 times in each X,

Y, or Z direction

8.4 to 150 Hz

9.8m/s

Under continuous

vibration

5 to 8.4 Hz

1.75 mm

8.4 to 150 Hz

4.9m/s

Shock resistant

Compliant with JIS B3502 and IEC61131-2 147m/s

(15G) Three times in each X, Y, or Z direction

Operating atmosphere

No greasy fumes, corrosive gas, flammable gas, excessive conductive dust, and direct sunlight (as well as at storage)

Operating altitude

2000 m or less

Installation location

Inside control panel

Overvoltage category



or less

Pollution degree

2 or less

Cooling method

Self-cooling

Grounding

Grounding with a ground resistance of 100

Ω

or less by using a ground cable that has a cross-sectional area of 0.14 to 1.5 mm

(solid wire), 0.14 to 1.0 mm

(stranded wire), or 0.25 to 0.5 mm

(rod terminal with an insulation sleeve).

If impossible, connect the ground cable to the control panel.

Item

Specifications

GT2103-PMBD

GT2103-PMBDS

GT2103-PMBDS2

GT2103-PMBLS

D i s p l a y
section

*1*2

Display device

TFT monochrome display

Screen size

3.8"

Resolution

320 × 128 dots

Display size

89.0(3.51) (W) × 35.6(1.41) (H) mm(inch)

Displayed number of

characters

16-dot standard font: 20 characters × 8 lines (two-byte characters)

12-dot standard font: 26 characters × 10 lines (two-byte characters)

Display color

Monochrome (black and white) 32 scales

B r i g h t n e s s

Adjustment

32 levels

Backlight

5 colors LED (white, green, pink, orange, red) (Not replaceable)

Backlight life

Approx. 50000 h (operating ambient temperature: 25°C, display intensity: 50%)

To u c h
panel

Type

Analog resistive film

Key size

Minimum 2 × 2 dots (per a key)

Simultaneous press

Simultaneous press prohibited

(only 1 point can be pressed)

Life

1 million times or more (Operating force: 0.98 N or less)

U s e r

memory

capacity

U s e r m e m o r y

capacity

Memory for storage (ROM): 3 MB

Life (number of write

times)

100000 times

B u i l t - i n

interface

RS-232 (rear face)

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: MINI-DIN6-pin

(female)

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: MINI-DIN6-pin

(female)

RS-232 (side face)

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: 9-pin terminal

block

RS-422/485

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: terminal block 5-

pin
Terminating resistor

: OPEN/110

Ω

/330

Ω

(Switched with the terminating

resistor setting switch)

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: terminal block 9-

pin
Terminating resistor

: OPEN/110

Ω

/330

Ω

(Switched with the terminating

resistor setting switch)

RS-422

1 channel Transmission speed:

115200/57600/38400/19200/9600/

4800 bps

Connector shape: 9-pin terminal

block

Ethernet

1 channel Data transfer method:

10BASE-T/100BASE-TX

Connector shape: RJ-45 (modular

jack)

*1 Bright dots (always lit) and dark dots (unlit) may appear on a liquid crystal display panel due to its characteristics. It is impossible to completely avoid this symptom, as

the liquid crystal display comprises of a great number of display elements. In addition, color tone difference, unevenness of brightness, or flickers may occur due to

individual differences of liquid crystal display panels. Please note that these symptoms occur due to GOT's characteristic and are not caused by product defect.

*2 Flicker may occur due to vibration, shock, or display color.
*3 Settings the screen saving backlight to OFF prevents the display screen from burn-in and enables the backlight to lengthen its life.
*4 When using a stylus pen, it will be 100,000 times. (The specifications must be satisfied the following condition.)

- Material: Polyacetal resin
- Tip radius: 0.8 mm or more

*5 If you touch two or more points on the touch panel simultaneously and a switch is placed between the two points, the switch may be activated. Do not touch two or more

points on the touch panel simultaneously.

*6 Set the terminating resistor selector switch of the GOT in accordance with the connection type when adopting GOT multidrop connection.
*7 It is necessary to mount the separately sold SD card unit (GT21-03SDCD).
*8 Note that this does not guarantee all users' operation environment. In addition, the GOT may not be usable in the environment where oil or chemicals are splashed over

for a long time or where oil mist is filled.

*9 113 (W) × 74 (H) × 32 (D) mm when the SD card unit (GT21-03SDCD) is mounted

1.3 Power Supply Specifications

2. Wiring of connection cable

The diagram below shows cable assignment for GOT port.
Cable for GT2103-PMBD: GT21-C



R4-8P5, GT21-C



R4-25P5

Cable for GT2103-PMBDS: GT10-C



R4-8P, GT10-C



R4-25P

Cable for GT2103-PMBDS2: GT10-C



R2-6P

Cable for GT2103-PMBLS: GT10-C



R4-8P

User-made cable is necessary, depending on the PLC.
For the detail, refer to GOT2000 Series Connection Manual.

B u i l t - i n

interface

USB (Device)

1 ch
Maximum transfer rate: Full-Speed 12 Mbps Connector shape: USB Mini-B

SD card

1 channel SDHC card supported (max. 32 GB)

Buzzer output

Single tone (tone length adjustable)

Productive structure

Outside the enclosure: IP67F

Inside the enclosure: IP2X

External dimensions

113(4.45) (W) × 74(2.92) (H) ×

32(1.26) (D) mm

113(4.45) (W) × 74(2.92) (H) × 27(1.07) (D) mm

113(4.45) (W) × 74(2.92) (H) ×

27(1.07) (D) mm

Panel cut dimensions

105(4.14) (W) × 66(2.6) (H) mm

Weight (excluding a fitting)

0.2 kg

0.18 kg

Compatible software package

GT Works3 Version1.112S or later

GT Works3 Version1.119Z or later

Item

Specifications

GT2103-PMBD

GT2103-PMBDS

GT2103-PMBDS2

GT2103-PMBLS

Item

Specifications

GT2103-PMBD

GT2103-PMBDS

GT2103-PMBDS2

GT2103-PMBLS

Input power supply voltage

DC24 V (+10%, -15%)

5VDC (±5%), supplied from the

PLC

P o w e r

consumption

Under the

maximum load

2.6 W or less

1.9 W or less

2.2 W or less

1.1 W or less

At backlight off 2.0 W

1.3 W

1.6 W

0.7 W

Inrush current

30 A or less (1ms, 25°C, at the maximum load)

P e r m i s s ib l e i n s ta n ta ne o u s

power failure time

Within 5ms

Noise immunity

Noise voltage: 1000 Vp-p, Noise width: 1

s (by noise simulator of 30 to 100 Hz noise frequency)

Dielectric withstand voltage

500 VAC for 1 minute (between the GOT’s power supply terminals and the GOT’s grounding terminal)

Insulation resistance

10 M

Ω

or larger by insulation resistance tester

(between the GOT’s power supply terminals and the GOT’s grounding terminal)

Electrical wire size

No. of wire per terminal: 1
Solid wire 0.14 to 1.5 mm

AWG26 to AWG16, Stranded wire 0.14 to 1.0 mm

AWG26 to AWG16, Ferrules with plastic sleeve 0.25 to 0.5 mm

AWG24 to AWG20

No. of wire per terminal: 2
Solid wire 0.14 to 0.5 mm

AWG26 to AWG20, Stranded wire 0.14 to 0.2 mm

AWG26 to AWG24

Ferrules with plastic sleeve

AI 0.25-6BU (AWG24), AI 0.34-6TQ (AWG22), AI 0.5-6WH (AWG20) (Phoenix Contact Inc.)

Crimper type

CRIMPFOXZA3 (Phoenix Contact Inc.)

Tightening torque (terminal

screws)

0.22 to 0.25 N·m

Cable jacket to remove

7 mm (0.27")

Tightening torque

0.22 to 0.25 N·m

Recommended Tool (Screwdriver)

SZS 0.4 × 2.5 (Phoenix Contact Inc.)

GT21-C

□□□

R4-8P5

GT10-C

□□□

R4-8P

24V

GOT

CSB

CSA

SDA
SDB
RDA
RDB
SG
RSA

RSB

Untied
wire
color

Brown
Red
Orange
Yellow
Green
Black

White

GT21-C

□□□

R4-25P5

GT10-C

□□□

R4-25P

24V
SDA
SDB
RDA
RDB
SG
RSA

RSB

CSB

CSA

Blue

Purple

(terminal
block)

GOT

Brown
Red
Orange
Yellow
Green

Black

White

Untied
wire
color

GT10-C

□□□

R2-6P

24V

SD
RD
ER
DR
SG
RS
CS

Blue

Purple

(terminal
block)

GOT

Brown
Red

Yellow
Green

*1 The cable for GT2103-PMBD does not have connections to the signals (RSA, RSB, CSA,CSB).

GOT

PLC

PLC connection cable

GT2103-PMBD, GT2103-PMBDS,

GT2103-PMBDS2, GT2103-PMBLS

GT21 General Description

This manual describes the part names, dimensions, mounting, and specifications
of the product. Before use, read this manual and manuals of relevant products
fully to acquire proficiency in handling and operating the product. Make sure to
learn all the product information, safety information, and precautions.
And, store this manual in a safe place so that you can take it out and read it
whenever necessary. Always forward it to the end user.
Registration
Ethernet is a trademark of Xerox Corporation in the United States. The company
name and the product name to be described in this manual are the registered
trademarks or trademarks of each company.

Effective Sep. 2016
Specifications are subject to change without notice.



2014 Mitsubishi Electric Corporation

Manual Number

JY997D61901C

Date

Sep. 2016