M70V Series Connection Manual
4.5 Connection of MITSUBISHI CNC Machine Operation Panel
145
<Software Interface>
Machine operation panel occupies RIO station No. 4 to 6. The device numbers for switch and LED on operation
panel are fixed as listed below.
The following lists the devices for using the RIO 1st channel.
Table: Device No. for Machine operation panel
(1) Machine operation panel B (Switch)
Machine operation panel B is equipped with rotary switches (cutting override, spindle override) and a selector
switch (memory protection key), and an emergency stop button. Direct wiring connection will be applied to the
emergency stop button, and device numbers for other switches are defined as listed below.
(a) Cutting override (6bit)
21 position code list
Station
Device No.
Detail
RIO1
RIO3
1
X00
~
X1F/Y00
~
Y1F
X200
~
X21F/Y200
~
Y21F
2
X20
~
X3F/Y20
~
Y3F
X220
~
X23F/Y220
~
Y23F
3
X40
~
X5F/Y40
~
Y5F
X240
~
X25F/Y240
~
Y25F
4
X60
~
X7F/Y60
~
Y7F
X260
~
X27F/Y260
~
Y27F
Machine operation panel B
(Switch)...16 points vacant
5
X80
~
X9F/Y80
~
Y9F
X280
~
X29F/Y280
~
Y29F
Machine operation panel A
(Key switch/LED)
6
XA0
~
XBF/YA0
~
YBF
X2A0
~
X2BF/Y2A0
~
Y2BF
Machine operation panel A
(Key switch/LED)
7
XC0
~
XDF/YC0
~
YDF
-
8
XE0
~
XFF/YE0
~
YFF
-
Device No.
Setting value X60 X61 X62 X63 X64 X65
0
0
0
0
0
0
0
1
1
0
0
0
0
1
2
1
1
0
0
0
0
3
0
1
0
0
0
1
4
0
1
1
0
0
0
5
1
1
1
0
0
1
6
1
0
1
0
0
0
7
0
0
1
0
0
1
8
0
0
1
1
0
0
9
1
0
1
1
0
1
10
1
1
1
1
0
0
11
0
1
1
1
0
1
12
0
1
0
1
0
0
13
1
1
0
1
0
1
14
1
0
0
1
0
0
15
0
0
0
1
0
1
16
0
0
0
1
1
0
17
1
0
0
1
1
1
18
1
1
0
1
1
0
19
0
1
0
1
1
1
20
0
1
1
1
1
0
Summary of Contents for M70V Series
