background image

5

Before Use

Do not allow flammable gas to be 

sucked inside or use the unit where 

flammable gas accumulates.

(Factory, beauty salon, etc.)

This may cause 

fire

.

Do not place the unit close to 

flammable objects or objects lit with 

fire, such as cigarettes or incense 

sticks. 

This may cause 

fire

.

Do not get on top of or lean against the 

unit. 

This may cause the unit to topple or fall and cause 

injury

.

Do not lay the unit horizontally when 

removing a filter.

This may cause dust to enter inside, resulting in 

fire 

or electric shock

.

Do not use a damaged filter or operate 

the unit while a filter is removed.

This may cause dust to enter inside, resulting in 

fire 

or electric shock

.

Do not install the unit where water may 

be spilt onto it or where there is a lot 

of humidity such as in a bathroom.

This may cause 

electric shock

.

Should water or other liquid be spilt onto the unit, stop 

operation and remove the power plug, and then contact 

the retail store where you purchased the product.

Do not use the unit in a location with the 

oily smoke of machine oil or other oil.

This may cause cracking, resulting in 

electric shock

.

Do not wipe the unit with benzene or 

thinner or spray insecticide or other 

chemicals onto it.

This may cause 

electric shock, fire, or cracking 

and cause injury

.

Do not operate the unit when using an 

insecticide that produces smoke.

An accumulation of chemical components may be released 

from the air outlet and be 

harmful to your health

.

After using an insecticide, ventilate the area sufficiently 

prior to operating the unit.

When using the unit in combination 

with a combustion appliance, ventilate 

the room occasionally.

Carbon monoxide cannot be removed from the air, 

so not ventilating the room may cause 

carbon 

monoxide poisoning

.

When disconnecting the power plug, 

pull it out straight while holding not the 

cord but the power plug.

Failure to do so may cause 

electric shock or a 

short circuit resulting in fire

.

When the unit will not be used for a 

long time, disconnect the power plug.

Failure to do so may cause the insulation to deteriorate, 

resulting in 

fire from a short circuit or an electric 

shock

.

This air purifier is designed for household use. 

Do not use it for industrial use.

Do not block the air 

inlets or outlet.

Do not use this unit 

instead of an exhaust fan 

or exhaust hood (there is 

no ventilation function).

Do not insert a finger or 

foreign object into the 

PM2.5 Sensor.

Do not use the 

unit while it is laid 

horizontally.

Do not use the unit while 

the inlet panel, pre-filter 

unit, HEPA filter, activated 

charcoal filter, or platinum 

catalyst is removed.

This may cause 

malfunction

.

This may cause the filter life 

to become shorter and cause 

deformation, discoloration, 

or malfunction

.

This may cause 

malfunction

.

This may cause 

malfunction

.

This may cause 

a malfunction

.

Attentions

CAUTION

en_ma-a85r-a_cs55.indd   5

2021/10/20   13:11:12

Summary of Contents for MA-E85R-A





















Reviews: