Mitsubishi Electric MDS-D-SPJ3 Specification Manual Download

Page: 29 / 284

4-5-2 Speed loop delay compensation
4-5-3 Dual feedback control

4-6 Settings for emergency stop

4-6-1 Deceleration control
4-6-2 Vertical axis drop prevention control
4-6-3 Vertical axis pull-up control

4-7 Protective functions

4-7-1 Overload detection
4-7-2 Excessive error detection
4-7-3 Collision detection function

4-8 Servo control signal

4-8-1 Servo control input (NC to Servo)
4-8-2 Servo control output (Servo to NC)

5 Spindle Adjustment

5-1 D/A output specifications for spindle drive unit

5-1-1 D/A output specifications
5-1-2 Setting the output data
5-1-3 Setting the output magnification

5-2 Adjustment procedures for each control

5-2-1 Basic adjustments
5-2-2 Gain adjustment
5-2-3 Adjusting the acceleration/deceleration

operation

5-2-4 Orientation adjustment
5-2-5 Synchronous tapping adjustment
5-2-6 Spindle C axis adjustment (For lathe

system)

5-2-7 Spindle synchronization adjustment (For

lathe system)

5-2-8 Deceleration coil changeover valid function

by emergency stop

5-2-9 High-response acceleration/deceleration

function

5-2-10 Spindle cutting withstand level

improvement

5-3 Settings for emergency stop

5-3-1 Deceleration control

5-4 Spindle control signal

5-4-1 Spindle control input (NC to Spindle)
5-4-2 Spindle control output (Spindle to NC)

6 Troubleshooting

6-1 Points of caution and confirmation

6-1-1 LED display when alarm or warning occurs

6-2 Protective functions list of units

6-2-1 List of alarms
6-2-2 List of warnings

6-3 Troubleshooting

6-3-1 Troubleshooting at power ON
6-3-2 Troubleshooting for each alarm No.
6-3-3 Troubleshooting for each warning No.
6-3-4 Parameter numbers during initial parameter

error

6-3-5 Troubleshooting the spindle system when

there is no alarm or warning

7 Maintenance

7-1 Periodic inspections

7-1-1 Inspections
7-1-2 Cleaning of spindle motor

7-2 Service parts
7-3 Adding and replacing units and parts

7-3-1 Replacing the drive unit
7-3-2 Replacing the unit fan
7-3-3 Replacing the battery

Appendix 1 Cable and Connector

Specifications

Appendix 1-1 Selection of cable

Appendix 1-1-1 Cable wire and assembly

Appendix 1-2 Cable connection diagram

Appendix 1-2-1 Battery cable
Appendix 1-2-2 Optical communication repeater

unit cable

Appendix 1-2-3 Servo / tool spindle detector cable
Appendix 1-2-4 Spindle detector cable

Appendix 1-3 Connector outline dimension drawings

Appendix 1-3-1 Optical communication cable
Appendix 1-3-2 DI/O or maintenance connector
Appendix 1-3-3 Servo detector connector
Appendix 1-3-4 Brake connector
Appendix 1-3-5 Power connector
Appendix 1-3-6 Drive unit side main circuit

connector

Appendix 1-3-7 Spindle detector connector

Appendix 2 Cable and Connector

Assembly

Appendix 2-1 CM10-SPxxS-x(D6) plug connector
Appendix 2-2 CM10-APxxS-x(D6) angle plug

connector

Appendix 2-3 CM10-SP-CV reinforcing cover for

straight plug

Appendix 2-4 CM10-AP-D-CV reinforcing cover for

angle plug

Appendix 2-5 1747464-1 plug connector

Appendix 2-5-1 Applicable products
Appendix 2-5-2 Applicable cable
Appendix 2-5-3 Related documents
Appendix 2-5-4 Assembly procedure

Appendix 3 Precautions in Installing

Spindle Motor

Appendix 3-1 Precautions in transporting motor
Appendix 3-2 Precautions in selecting motor fittings
Appendix 3-3 Precautions in mounting fittings
Appendix 3-4 Precautions in coupling shafts
Appendix 3-5 Precautions in installing motor in

machine

Appendix 3-6 Other Precautions
Appendix 3-7 Example of unbalance correction