MDS-E/EH Series Instruction Manual
4 Setup
138
IB-1501229-F
bit 7-0: mtyp(HEX-2,1) Motor type
Set the motor type. Set this with SV017/bitF-C.
For SV017/bitF-C = 1 (200V standard motor series)
HG75 : 41h HG123 : 64h
HG105 : 42h HG142 : 65h
HG54 : 43h HG46 : BAh
HG104 : 44h HG56 : BBh
HG154 : 45h 4Fh(Note 1) HG96 : BCh
HG224 : 46h
HG204 : 47h
HG354 : 48h
HG223 : 66h
HG303 : 68h
HG453 : 49h
HG703 : 4Ah
HG903 : 4Bh
HG302 : 67h
(Note 1) When MDS-E-V3 is connected
For SV017/bitF-C = 3 (400V standard motor series)
HG-H75 : 41h HQ-H903 : 58h
HG-H105 : 42h HQ-H1103 : 59h
HG-H54 : 43h
HG-H104 : 44h
HG-H154 : 45h
HG-H204 : 47h
HG-H354 : 48h
HG-H453 : 49h
HG-H703 : 4Ah
HG-H903 : 4Bh
HG-H1502 : 4Dh
For linear motor and direct-drive motor, follow the settings stated in respective materials.
Set the excessive error detection width during servo OFF.
When set to "0", the excessive error alarm detection will be ignored, so do not set to "0".
<Standard setting value>
OD1=OD2= (Rapid traverse rate [mm/min]) / (60×PGN1) / 2 [mm]
Related parameters: SV023
---Setting range---
0 to 32767 (mm)
However, when SV084/bitC=1, the setting range is from 0 to 32767 (
μ
m).
#2226
SV026 OD2
Excessive error detection width during servo OFF
Summary of Contents for MDS-E
