MDS-E/EH Series Instruction Manual
4 Setup
214
IB-1501229-F
Set this parameter when the limit cycle occurs in the full-closed loop or overshooting occurs in positioning.
When setting this parameter, make sure to set the torque offset "SP050(TOF)".
When not using, set to "0".
---Setting range---
0 to 32767
Normally SP005(VGN1) is used.
By setting "SP035/bit1, SP035/bit9 or SP036/bit1=1", gain 2 can be used according to the application.
Gain 2 can also be used by setting "Speed gain set 2 changeover request (control input 5/ bitC) = 1".
Refer to SP005(VGN1) for adjustment procedures.
---Setting range---
1 to 9999
Normally SP006(VIA1) is used.
By setting "SP035/bit1, SP035/bit9 or SP036/bit1=1", gain 2 can be used according to the application.
Gain 2 can also be used by setting "Speed gain set 2 changeover request (control input 5/ bitC) = 1".
Refer to SP006(VIA1) for adjustment procedures.
---Setting range---
1 to 9999
Normally SP007(VIL1) is used.
By setting "SP035/bit1, SP035/bit9 or SP036/bit1=1", gain 2 can be used according to the application.
Gain 2 can also be used by setting "Speed gain set 2 changeover request (control input 5/ bitC) = 1".
Refer to SP007(VIL1) for adjustment procedures.
---Setting range---
0 to 32767
Not used. Set to "0".
Not used. Set to "0".
Not used. Set to "0".
Set the minimum value for the variable excitation rate. The standard setting is "50".
Set to "0" when using an IPM spindle motor.
If noise including gear noise is loud, select a small value. However, a larger setting value is more effective
for impact response.
(Note) When setting a value at "50 or more", check if there is no problem with gear noise, motor excitation
noise, vibration during low-speed rotation or vibration when the servo is locked during orientation stop, etc.
When setting a value at "less than 50", check if there is no problem with the impact load response or rigidity
during servo lock.
---Setting range---
0 to 100 (%)
#13007
SP007 VIL1
Speed loop delay compensation 1
#13008
SP008 VGN2
Speed loop gain 2
#13009
SP009 VIA2
Speed loop lead compensation 2
#13010
SP010 VIL2
Speed loop delay compensation 2
#13011
SP011
#13012
SP012
#13013
SP013
#13014
SP014 PY1
Minimum excitation rate 1
Summary of Contents for MDS-E
