MDS-E/EH Series Instruction Manual
4 Setup
244
IB-1501229-F
Select the spindle functions.
Functions are allocated to each bit.
Set this in hexadecimal format.
bit F-C :
Not used. Set to "0".
bit B : pfdsr
Set the spindle stop operation at a power failure when the deceleration and stop function at power failure is
enabled.
Normal (Coast to a stop at power failure) : 0
Deceleration and stop at power failure : 1
bit A-9 :
Not used. Set to "0".
bit 8 : nohis History of communication error alarm between NC and DRV(34,36,38,39)
0: Enable 1: Disable
bit 7 : cse Spindle C axis command speed monitoring function
0: Normal setting (function disabled) 1: Function enabled
bit 6-0 :
Not used. Set to "0".
Related parameters: SP055, SP056
Not used. Set to "0000".
Not used. Set to "0000".
When 100% is set, the voltage equivalent to the logical non-energized time will be compensated.
When "0" is set, 100% compensation will be performed.
Adjust in increments of 10% from the default value 100%.
If the value is too large, vibration or vibration noise may be generated.
---Setting range---
0 to 255 (%)
Not used. Set to "0".
Set the magnification in converting the thermistor temperature to the control compensation amount.
When "0" is set, the temperature compensation function is disabled.
When not using, or when using an IPM spindle motor, set to "0".
---Setting range---
0 to 400 (%)
#13230
SP230 SFNC10
Spindle function 10
#13231
SP231
#13232
SP232
#13233
SP233 IVC
Voltage non-sensitive band compensation
#13234
SP234
(PR)
#13235
SP235 R2H
Temperature compensation gain
cse
nohis
pfdsr
Summary of Contents for MDS-E
