MDS-E/EH Series Instruction Manual
6 Spindle Adjustment
372
IB-1501229-F
bitB. In minimum excitation rate 2 selection (PY2)
[1] When PY2=1 is set, the minimum excitation rate 2 (SP015) is being selected.
[2] When PY2=0 is set, the minimum excitation rate 1(SP014) is being selected.
bitC. In speed gain set 2 selection (VG2)
[1] When VG2=1 is set, the gain parameter (SP008/SP009/SP010) used in the speed loop isbeing selected.
[2] When VG2=0 is set, the gain parameter (SP005/SP006/SP007) used in the speed loop isbeing selected.
bitD. Zero point re-detection complete
If the zero point re-detection is completed after the zero point re-detection request (control input5/bitD) is set
to1, ORF=1 is set. If the zero point re-detection request is set to 0, ORF=0 is set.
bitF. In 2nd in-position (INP2)
The status changes to INP2=1 when position droop exists within the in-position area set by parameter SP025
(INP2) regardless of serve ON or OFF.
(Note)
The bits other than those above are used for maintenance.
(6) Spindle control output 6
bit0. In OMR-FF control (OMRFF)
OMRFF=1 (enabled) if OMR-FF control is enabled.
bit8. In drivers communication control (DD1)
DD1=1 (enabled) if high-speed synchronous tapping control is enabled.
(Note)
The bits other than those above are used for maintenance.
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
bit
0
1
2
3
4
5
6
7
8
9
A
B
C
D
E
F
DD1
-
-
-
-
-
-
-
-
-
-
-
-
-
-
DD1
OMRFF
OMRFF
Name
Details
Spindle
control output 6
Details
In drivers communication control
In OMR-FF control
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
(For maintenance)
Summary of Contents for MDS-E
