Requirement for Compliance with LVD directive
The following products have shown compliance through direct
testing (of the identified standards below) and design analysis
(through the creation of a technical construction file) to the European
Directive for Low Voltage (73/23/EEC) when used as directed by the
appropriate documentation.
Type :
Programmable Controller (Open Type Equipment)
Models : MELSEC FX
2NC
series manufactured
from August 1st, 1999
FX
2NC
-16EYR-T-DS
from October 1st, 2007
FX
2NC
-16EYR-T
*Compliance to BSEN61010-1 is claimed through virtue of direct
compliance to IEC1010-1 and Amendment 1.
Models :MELSEC FX
2N
series manufactured
from July 1st, 1997
FX
2N
-16EYR-ES/UL
from August 1st, 2005 FX
2N
-8ER-ES/UL
FX
2N
-8EYR-ES/UL
For the products above, PLC’s manufactured
before March 31st, 2002 are compliant with IEC1010-1
PLC’s manufactured from April 1st, 2002 to April 30th, 2006 are
compliant with EN61131-2:1994+A11:1996+A12:2000
PLC’s manufactured after May 1st, 2006 are compliant with
EN61131-2:2003
Caution for compliance with EC Directive
Installation in Enclosure
Programmable logic controllers are open-type devices that must be
installed and used within conductive control boxes. Please use the
FX
3UC
Series programmable logic controllers while installed in
conductive shielded control boxes. Please secure the control box lid
to the control box (for conduction). Installation within a control box
greatly affects the safety of the system and aids in shielding noise
from the programmable logic controller.
Caution for Analog Products in use
The analog special adapters have been found to be compliant to the
European standards in the aforesaid manual and directive. However,
for the very best performance from what are in fact delicate
measuring and controlled output device Mitsubishi Electric would like
to make the following points;
As analog devices are sensitive by nature, their use should be
considered carefully. For users of proprietary cables (integral with
sensors or actuators), these users should follow the manufacturers’
installation requirements.
Mitsubishi Electric recommends that shielded cables be used. If no
other EMC protection is provided, then users may experience
temporary loss of accuracy b10%/-10% in very heavy
industrial areas.
However, Mitsubishi Electric suggests that when adequate EMC
precautions are followed with general good EMC practice for the
users complete control system, users should expect normal
accuracy as specified in this manual.
- Sensitive analog cables should not be laid next to or bound with
high voltage cabling. Where possible, users should run analog
cables separately.
- Good cable shielding should be used. When grounding the
shield - ensure that no loops are accidentally created.
- When reading analog values, EMC induced errors can be
smoothed out by averaging the readings. This can be achieved
either through functions on the analog special adapter/block or
through the user’s program in the FX
3UC
Series PLC main unit.
Associated manuals
FX
3UC
Series PLC (main unit) comes with this document (hardware
manual).
For a detailed explanation of the FX
3UC
Series hardware and
information on PLC programming instructions and special extension
unit/block, refer to the relevant documents.
EN61131-2:2003
Programmable
controllers
- Equipment
requirements and
tests
Compliance with all relevant aspects of
the standard.
•
Radiated Emissions
•
Mains Terminal Voltage Emissions
•
RF immunity
•
Fast Transients
•
ESD
•
Surge
•
Voltage drops and interruptions
•
Conducted
•
Power magnetic fields
Standard
Remark
IEC1010-1:1990
/A1:1992
BSEN61010-1 :1993 *
Safety requirements for
electrical equipment for
measurement, control, and
laboratory use
- General requirements
The equipment has been
assessed as a component for
fitting in a suitable enclosure
which meets the requirements of
IEC 1010-1:
1990+A1:1992
Standard
Remark
IEC1010-1:1990
/A1:1992
Safety requirements for
electrical equipment for
measurement, control, and
laboratory use
- General requirements
The equipment has been
assessed as a component for
fitting in a suitable enclosure
which meets the requirements of
IEC 1010-1:
1990+A1:1992
EN61131-2:1994 :2003
/A12:2000
/A11:1996
Programmable controllers
- Equipment requirements
and tests
The equipment has been
assessed as a component for
fitting in a suitable enclosure
which meets the requirements of
EN61131-2:
1994+A11:1996+A12:2000,
:2003
Standard
Remark
Manual name
Manual No.
Description
FX
3UC
Series
User's Manual
- Hardware
Edition
JY997D28701
MODEL CODE:
09R519
Explains the FX
3UC
Series
PLC specifications for I/O,
wiring, installation, and
maintenance.
FX
3U
/FX
3UC
Series
Programming
Manual
- Basic & Applied
Instruction Edition
JY997D16601
MODEL CODE:
09R517
Describes PLC
programming for basic/
applied instructions STL/
SFC programming and
system devices.
FX Series User’s
Manual - Data
Communication
Edition
JY997D16901
MODEL CODE:
09R715
Explains N:N Network,
parallel link, computer link,
non-protocol
communication by RS
instructions/FX
2N
-232IF.
FX
3U
/ FX
3UC
Series
User's Manual
- Analog Control
Edition
JY997D16701
MODEL CODE:
09R619
Describes specifications for
analog control and
programming methods for
the FX
3U
/ FX
3UC
Series
PLC.
How to obtain manuals
For product manuals or documents, consult with the Mitsubishi
Electric dealer from who you purchased your product.
Incorporated Items
Verify that the following product and items are included in the
package.
1.
Outline
1.1
Part names
FX
3U
/ FX
3UC
Series
User's Manual
- Positioning
Control Edition
JY997D16801
MODEL CODE:
09R620
Explains the positioning
control specifications of the
FX
3U
/ FX
3UC
Series and
programming procedures
Included Items
Main units
FX
3UC
-
MT/D
Product
1 unit
FX
2NC
-100MPCB
[1m (3’ 3"), three wire]
1 cable
FX
2NC
-100BPCB
[1m (3’ 3"), two wire]
1 cable
Manuals [Japanese version,
English version]
1 manual
each
FX
3UC
-
MT/DSS
Product
1 unit
FX
2NC
-100MPCB
[1m (3’ 3"), three wire]
1 cable
Manuals [Japanese version,
English version]
1 manual
each
Input / output extension blocks
FX
2NC
-
EX
FX
2NC
-16EX-T
Product
1 unit
FX
2NC
-10BPCB1 [0.1m (3.93"),
double-ended]
1 cable
FX
2NC
-
EX-DS
FX
2NC
-16EX-T-DS
FX
2NC
-
EYT
FX
2NC
-
EYT-DSS
FX
2NC
-16EYR-T
FX
2NC
-16EYR-T-DS
Product
1 unit
Manual name
Manual No.
Description
[2]
[5]
Front panel
[11]
[6]
[12]
[2]
[8]
[4]
[2]
[6]
[14]
Under side
[4]
[15]
[7]
[9]
[10]
[6]
No.
Name
[1]
Memory cassette dummy cover
[2]
Special adapter connecting hooks
[3]
Special adapter connector cover
[4]
DIN rail mounting hooks
[5]
POW LED
On while power is on the PLC.
RUN LED
On while the PLC is running.
BAT LED
Lights when the battery voltage drops.
ERR LED
Flashing when a program error occurs.
Lights when a CPU error occurs.
[6]
FX
2NC
/FX
3UC
Extension block connecting hooks
[7]
Input LED
[8]
Output LED
[9]
Input connector
[10] Output connector
[11] Peripheral device connecting connector (RS-422)
[12] RUN/STOP switch
[13] FX
2NC
/FX
3UC
Extension block connecting connector cover
[14] Power connector for main unit
[15] Battery cover
Green
Green
Red
Red
[1]
[3]
Left side
[2]
[4]
[4]
[13]
Right side
[2]
[6]
[6]
Display LED
[5]
