Mitsubishi Electric MELSEC Q80BD-J71GF11-T2 User Manual Download

Page: 173 / 248

16 TROUBLESHOOTING

16.9 Error Code List

171

D257H

Request type error (REQ)

Check the request type in the request data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D258H

Specified/current control station not
exist (dedicated instruction)

Check the target station number, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D259H

Mode error during dedicated
instruction execution

Change the mode of the master station from "Loop test" to "Online", and execute it again.
If this error persists, please consult your local Mitsubishi representative.

D25AH

Channel in use (dedicated
instruction)

Retry it after a little while.
Change the channel for the own or target station.

D25BH

Channel in use (dedicated
instruction)

Change the channel for the own or target station.

D25CH

Dedicated instruction error

An invalid value is set for the control block of the dedicated instruction. Correct the value, and then retry
the operation.
If this error persists, please consult your local Mitsubishi representative.

D25DH

Incorrect transient data

Check the transient data at the request source, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D25EH

Dedicated instruction error

Another CC-Link dedicated instruction is in execution. Retry it after a little while.
If this error persists, please consult your local Mitsubishi representative.

D25FH

Station type error (REMFR/REMTO
executing station)

The REMFR/REMTO instruction is not available for stations other than master and local stations. Modify
the program so that the REMFR/REMTO instruction will not be used.

D260H

Station type error (REMTO
executing station)

The REMTO instruction is not available for local stations. The REMTO instruction must be executed on
the master station.

D261H

Station type error (CCPASET
executing station)

Parameter setting using the CCPASET instruction is not available for local stations. It must be executed
to the master station.

D262H

Number of total slave stations setting
error (CCPASET)

Correct the number of total slave stations in the control data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D263H

Constant link scan time setting error
(CCPASET)

Correct the constant link scan time in the control data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D264H

Station No. range error (CCPASET)

Change the station number in the setting data to any of 1 to 120, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D265H

Duplicate station No. (CCPASET)

Correct the station number in the setting data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D266H

Number of total slave stations error
(CCPASET)

Correct the number of total slave stations in the setting data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D267H

Station type error (CCPASET)

Change the station type value in the setting data to any of 0 to 3, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D268H

Device range assignment error
(CCPASET)

Correct the link device offset or size of slave station(s) in the setting data, and retry the operation.
If this error persists, please consult your local Mitsubishi representative.

D269H

Target station type error

Set the target station number in the REMFR/REMTO instruction to the station number of an intelligent
device station.

D26AH

Target station No. error

Reconnect the target station of the REMFR/REMTO instruction.

D26BH

Network No. error (CCPASET
executing station)

Set any of 1 to 239 to Switch 1 (network No.) in the intelligent function module switch setting of the
master/local module.

D26CH

Station No. error (CCPASET
executing station)

When activating as a master station, set 0 to Switch 2 in the intelligent function module switch setting of
the master/local module.
When activating as a local station by the CCPASET instruction, use a master/local module with a serial
number whose first five digits are '12072' or higher.
When activating as a local station, set a value within the range from 3101H to 3178H to Switch 2 in the
intelligent function module switch setting of the master/local module.

D26DH

Mode error (CCPASET executing
station)

Set 0 to Switch 3 in the intelligent function module switch setting of the master/local module

D280H

Transient data request error

Correct the request command at the request source, and retry the operation.

D281H

Transient reception failed

Check the network condition by CC-Link IE Field Network diagnostics, and take action.
When the target station is overloaded and cannot receive transient data, send the data to the target
station after the load on the station is reduced.

D282H

Receive queue full

Temporarily stop the transient transmission, and then retry the operation.
Reduce the frequency of transient transmission and then retry the operation.
Use the COM instruction to increase the frequency of transient transmission.
If this error persists, please consult your local Mitsubishi representative.

D283H

Transient transmission failed

Check the network condition by CC-Link IE Field Network diagnostics, and take action.
Exchange the cables between PORT1 and PORT2 of the request source and retry the operation.
Reduce the frequency of transient transmission and then retry the operation.

Error
code

Error code

Corrective action