manualshive.com logo in svg

Mitsubishi Electric MR-J4-100B(-RJ), Instruction Manual

The Mitsubishi Electric MR-J4-100B(-RJ) is a cutting-edge industrial servo amplifier, designed to deliver exceptional performance and precision control. To operate this high-tech device, make sure to access the comprehensive Instruction Manual available for free download on our website. Explore the detailed manual packed with valuable insights and guidelines only at 88.208.23.73:8080.

Share
Download
background image

APPENDIX 

App. -  63 

 

App. 13 Optional data monitor function 

The optional data monitor function is used to monitor data in the servo amplifier with the servo system 
controller. In the optional data monitor function, data types of registered monitor and transient command can 
be set. 
For details of usage, the unit of data types, and others, refer to the manuals for servo system controllers. 
 
App. 13.1 Registered monitor 

Data type 

Description 

Effective load ratio 

The continuous effective load current is displayed. 
The effective value is displayed considering a rated current as 100%. 

Regenerative load ratio 

The ratio of regenerative power to permissible regenerative power is displayed in %. 

Peak load ratio 

The maximum torque generated is displayed. 
The highest value in the past 15 s is displayed, with the rated torque being 100%. 

Position feedback 

Feedback pulses from the servo motor encoder are counted and displayed. 

Encoder position within one revolution 

The position in servo motor-side 1-revolution is displayed in the encoder pulse unit. 
When the value exceeds the maximum number of pulses, it resets to 0. 

Encoder multiple revolution counter 

The rotation amount of the servo motor is displayed. The value is counted up by one per 
servo motor revolution. 

Load inertia moment ratio 

The set ratio of the load inertia moment to the servo motor shaft inertia moment is 
displayed. 

Load to motor mass ratio 

The load to mass of the linear servo motor primary-side ratio is displayed. 

Model loop gain 

The model loop gain value is displayed. 

Main circuit bus voltage  

The voltage of main circuit converter (between P+ and N-) is displayed. 

Cumulative current value 

The cumulative current value of the servo motor is displayed. 

Servo motor speed 

The servo motor speed is displayed. 

Servo motor speed 

The linear servo motor speed is displayed at linear servo motor driving. 

Selected droop pulse 

The droop pulse set in [Pr. PE10] is displayed. 

Module power consumption 

The module power consumption is displayed. 
The positive value is displayed in power running. The negative value is displayed in 
regeneration. 

Module integral power consumption 

The module integral power consumption is displayed. 

Instantaneous torque 

The instantaneous torque is displayed. 
The value of torque being occurred is displayed in real time considering a rated torque as 
100%. 

Instantaneous thrust 

The instantaneous thrust is displayed at linear servo motor driving. 
The value of thrust being occurred is displayed in real time considering a continuous thrust 
as 100%. 

Load-side encoder information 1 

When an incremental type linear encoder is used for the load-side encoder, the Z-phase 
counter of the load-side encoder is displayed by encoder pulses. 
When an absolute position type linear encoder is used for the load-side encoder, the 
encoder absolute position is displayed. 

Load-side encoder information 2 

When an incremental type linear encoder is used for the load-side encoder, the display 
shows 0. 
When an absolute position type linear encoder is used for the load-side encoder, the 
display shows 0. 
When a rotary encoder is used for the load-side encoder, the display shows the multi-
revolution counter value of the encoder. 

Z-phase counter 

The Z-phase counter is displayed in the encoder pulse unit. 
For an incremental type linear encoder, the Z-phase counter is displayed. The value is 
counted up from 0 based on the home position (reference mark). 
For an absolute position type linear encoder, the encoder absolute position is displayed. 

Servo motor thermistor temperature 

The thermistor temperature is displayed for the servo motor with a thermistor. 
For the servo motor without thermistor, "9999" is displayed. 
For the servo motor with a thermistor, refer to each servo motor instruction manual. 

Disturbance torque 

The difference between the torque necessary to drive the servo motor and the actually 
required torque (Torque current value) is displayed as the disturbance torque. 

Disturbance thrust 

The difference between the thrust necessary to drive the linear servo motor and the 
actually required thrust (Thrust current value) is displayed as the disturbance thrust. 

 

Summary of Contents for MR-J4-100B(-RJ)



































































































































































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4-100B(-RJ)

Unitek TVD6.2-RS Manual preview
TVD6.2-RS
Brand: Unitek Pages: 50
Emerson DX-208 User Manual preview
DX-208
Brand: Emerson Pages: 70
Emerson SP1201 Installation Manual preview
SP1201
Brand: Emerson Pages: 220
Peaco Support 2S-0.5G-B User Manual preview
2S-0.5G-B
Brand: Peaco Support Pages: 244
TECO T-Verter E2 Series Operating Manual preview
T-Verter E2 Series
Brand: TECO Pages: 64
BONMET SDL10A User Manual preview
SDL10A
Brand: BONMET Pages: 85
Shihlin SS2 Series Installation Manual preview
SS2 Series
Brand: Shihlin Pages: 4
Parker IM20 Series Product Manual preview
IM20 Series
Brand: Parker Pages: 74
Parker OEM750 User Manual preview
OEM750
Brand: Parker Pages: 96
gefran AGy-L 2040 Installation And Commissioning Manual preview
AGy-L 2040
Brand: gefran Pages: 18
hager h250 HXC04 H Series User Instructions preview
h250 HXC04 H Series
Brand: hager Pages: 4
Technosoft iPOS4803-SY3 Technical Reference preview
iPOS4803-SY3
Brand: Technosoft Pages: 37
YASKAWA CIMR-AC4A WAA Series Quick Start Manual preview
CIMR-AC4A WAA Series
Brand: YASKAWA Pages: 38
Oerlikon S16A2 Service Manual preview
S16A2
Brand: Oerlikon Pages: 56
Danfoss AME 685 Operating Manual preview
AME 685
Brand: Danfoss Pages: 20
Danfoss VLT 3032 Service Manual preview
VLT 3032
Brand: Danfoss Pages: 43
Danfoss VLT MCB 115 Installation Manual preview
VLT MCB 115
Brand: Danfoss Pages: 16
Minarik BOSS Series User Manual preview
BOSS Series
Brand: Minarik Pages: 56

Brands by name

Popular brands

Load more brands