manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

5. PARAMETERS 

5 -  35 

 

No. 

Symbol 

Name and function 

Initial 
value 

[unit] 

Setting 

 range 

Each/ 

Common 

PB53 VRF22 Vibration 

suppression control 2 - Resonance frequency 

Set the resonance frequency for vibration suppression control 2 to suppress low-
frequency machine vibration. 
To enable the setting value, set "Vibration suppression mode selection" to "3 inertia 
mode (_ _ _ 1)" in [Pr. PA24]. 
When "Vibration suppression control 2 tuning mode selection" is set to "Automatic 
setting (_ _ 1 _)" in [Pr. PB02], this parameter will be set automatically. When "Manual 
setting (_ _ 2 _)" is selected, the setting written to the parameter is used. 
The setting range of this parameter varies, depending on the value in [Pr. PB07]. If a 
value out of the range is set, the vibration suppression control will be disabled. Refer 
to section 7.1.5 for details. 

100.0 

[Hz] 

0.1 to  
300.0 

Each 

PB54 

VRF23  Vibration suppression control 2 - Vibration frequency damping 

Set a damping of the vibration frequency for vibration suppression control 2 to 
suppress low-frequency machine vibration. 
To enable the setting value, set "Vibration suppression mode selection" to "3 inertia 
mode (_ _ _ 1)" in [Pr. PA24]. 
When "Vibration suppression control 2 tuning mode selection" is set to "Automatic 
setting (_ _ 1 _)" in [Pr. PB02], this parameter will be set automatically. When "Manual 
setting (_ _ 2 _)" is selected, the setting written to the parameter is used. Refer to 
section 7.1.5 for details. 

0.00 

0.00 to  

0.30 

Each 

PB55 

VRF24  Vibration suppression control 2 - Resonance frequency damping 

Set a damping of the resonance frequency for vibration suppression control 2 to 
suppress low-frequency machine vibration. 
To enable the setting value, set "Vibration suppression mode selection" to "3 inertia 
mode (_ _ _ 1)" in [Pr. PA24]. 
When "Vibration suppression control 2 tuning mode selection" is set to "Automatic 
setting (_ _ 1 _)" in [Pr. PB02], this parameter will be set automatically. When "Manual 
setting (_ _ 2 _)" is selected, the setting written to the parameter is used. Refer to 
section 7.1.5 for details. 

0.00 

0.00 to  

0.30 

Each 

PB56  VRF21B  Vibration suppression control 2 - Vibration frequency after gain switching 

Set the vibration frequency for vibration suppression control 2 when the gain switching 
is enabled. 
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB52]. 
To enable this, select "3 inertia mode (_ _ _ 1)" of "Vibration suppression mode 
selection" in [Pr. PA24]. 
This parameter will be enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ 2 _)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.0 

[Hz] 

0.0 to  
300.0 

Each 

PB57  VRF22B  Vibration suppression control 2 - Resonance frequency after gain switching 

Set the resonance frequency for vibration suppression control 2 when the gain 
switching is enabled. 
When you set a value less than 0.1 Hz, the value will be the same as [Pr. PB53]. 
To enable this, select "3 inertia mode (_ _ _ 1)" of "Vibration suppression mode 
selection" in [Pr. PA24]. 
This parameter will be enabled only when the following conditions are fulfilled. 

"Gain adjustment mode selection" in [Pr. PA08] is "Manual mode (_ _ _ 3)". 
"Vibration suppression control 2 tuning mode selection" in [Pr. PB02] is "Manual 

setting (_ _ 2 _)". 

"Gain switching selection" in [Pr. PB26] is "Control command from controller is 

enabled (_ _ _ 1)". 

Switching during driving may cause a shock. Be sure to switch them after the servo 
motor or linear servo motor stops. 

0.0 

[Hz] 

0.0 to  
300.0 

Each 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Cambridge Audio 851E User Manual preview
851E
Brand: Cambridge Audio Pages: 16
Lab.gruppen FP+ Series FP 10000Q Technical Data preview
FP+ Series FP 10000Q
Brand: Lab.gruppen Pages: 2
Accuphase E-550 Service Information preview
E-550
Brand: Accuphase Pages: 33
Genz Benz Shen Pro LT Owner'S Manual preview
Shen Pro LT
Brand: Genz Benz Pages: 8
Evolveo Amp1 Manual preview
Amp1
Brand: Evolveo Pages: 11
Traynor IronHorse DH40H Service Manual preview
IronHorse DH40H
Brand: Traynor Pages: 9
Monacor PA-6000RC Instruction Manual preview
PA-6000RC
Brand: Monacor Pages: 50
Engl Steve Morse Signature 100 Operating Manual preview
Steve Morse Signature 100
Brand: Engl Pages: 37
ICON ProAudio HyperDrive HD1 Quick Start Manual preview
HyperDrive HD1
Brand: ICON ProAudio Pages: 11
Boss Audio Systems Chaos REV-2000D User Manual preview
Chaos REV-2000D
Brand: Boss Audio Systems Pages: 12
DC 1100.1 Owner'S Manual preview
1100.1
Brand: DC Pages: 8
Rajani VOD-50 Owner'S Manual preview
VOD-50
Brand: Rajani Pages: 10
Harley Benton HBW-150 User Manual preview
HBW-150
Brand: Harley Benton Pages: 28
ifi T188-250 Operating And Maintenance Instructions Manual preview
T188-250
Brand: ifi Pages: 35
Ltech LT-122 Quick Start Manual preview
LT-122
Brand: Ltech Pages: 2
Citronic CX-8088 170.353 User Manual preview
CX-8088 170.353
Brand: Citronic Pages: 2
Audio Note ONGAKU Kensei Owner'S Information preview
ONGAKU Kensei
Brand: Audio Note Pages: 16
Parasound NewClassic Model 2250 Owner'S Manual preview
NewClassic Model 2250
Brand: Parasound Pages: 16

Brands by name

Popular brands

Load more brands