Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 167 / 588

background image

6. NORMAL GAIN ADJUSTMENT

6 - 14

(5) If an error occurs

If a tuning error occurs during tuning, one-touch tuning will be stopped. With that, the following error
code will be displayed in status. Check the cause of tuning error. When executing one-touch tuning
again, stop the servo motor once. In addition, after returning the moving part to the tuning start position,
execute it.

Display

Name

Error detail

Corrective action example

C000

Tuning canceled

"Stop" was clicked during one-touch tuning.

C001

Overshoot exceeded

Overshoot amount is a value larger than the
one set in [Pr. PA10 In-position range] and
[Pr. PA25 One-touch tuning - Overshoot
permissible level].

Increase the in-position range or overshoot
permissible level.

C002

Servo-off during tuning

The one-touch tuning was attempted in the
user command method during servo-off.
The servo amplifier will be servo-off status
during one-touch tuning.

When executing one-touch tuning in the user
command method, turn to servo-on, and then
execute it.
Prevent the servo amplifier from being the
servo-off status during one-touch tuning.

C003

Control mode error

1. The one-touch tuning was attempted while

the torque control mode was selected in
the control modes.

Select the position control mode or speed
control mode for the control mode from the
controller, and then execute one-touch tuning.
Do not change the control mode during the
one-touch tuning.

2. During one-touch tuning, the control mode

was attempted to change from the position
control mode to the speed control mode.

C004

Time-out

1. One cycle time during the operation has

been over 30 s.

Set one cycle time during the operation (time
from the command start to the next command
start) to 30 s or less.

2. The command speed is slow.

Set the servo motor speed to 100 r/min or
higher. Error is less likely to occur as the
setting speed is higher.
When one-touch tuning by the amplifier
command is used, set a permissible travel
distance so that the servo motor speed is 100
r/min or higher. Set a permissible travel
distance to two or more revolutions as a guide
value to set the servo motor speed to 100
r/min.

3. The operation interval of the continuous

operation is short.

Set the stop interval during operation to 200
ms or more. Error is less likely to occur as the
setting time is longer.

C005

Load to motor inertia
ratio misestimated

1. The estimation of the load to motor inertia

ratio at one-touch tuning was a failure.

Drive the motor with meeting conditions as
follows.

The acceleration time constant/deceleration

time constant to reach 2000 r/min (mm/s) is
5 s or less.

Speed is 150 r/min (mm/s) or higher.
The load to servo motor (mass of linear

servo motor's primary side or direct drive
motor) inertia ratio is 100 times or less.

The acceleration/deceleration torque is

10% or more of the rated torque.

2. The load to motor inertia ratio was not

estimated due to an oscillation or other
influences.

Set to the auto tuning mode that does not
estimate the load to motor inertia ratio as
follows, and then execute the one-touch
tuning.

Select "Auto tuning mode 2 (_ _ _ 2)",

"Manual mode (_ _ _ 3)", or "2 gain
adjustment mode 2 (_ _ _ 4)" of "Gain
adjustment mode selection" in [Pr. PA08].

Manually set [Pr. PB06 Load to motor

inertia ratio/load to motor mass ratio]
properly.

«
...
165
166
167
168
169
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: JEFF ROWLAND Pages: 13

Brand: Nakamichi Pages: 24

Brand: Laney Pages: 4

Brand: Ultimate Pages: 24

LM3886 Overture

Brand: Texas Instruments Pages: 24

Brand: Kicker Pages: 20

Brand: Absolute Measurement Pages: 10

Brand: Audiovox Pages: 12

Brand: Park Pages: 24

Brand: Macrom Pages: 12

Brand: IMG STAGELINE Pages: 18

Brand: Hartke Pages: 20

Brand: B&K Pages: 16

Brand: Tapco Pages: 34

Brand: Atoll Electronique Pages: 3

Brand: Harman Pages: 10

Brand: Inter-m Pages: 20

Brand: Taiden Pages: 99

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands