manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

1. FUNCTIONS AND CONFIGURATION 

1 -  1 

 

1. FUNCTIONS AND CONFIGURATION 

POINT 

 

In MELSERVO-J4 series, ultra-small capacity servo amplifiers compatible with 
48 V DC and 24 V DC power supplies are available as MR-J4W2-0303B6. Refer 
to chapter 18 for details of MR-J4W2-0303B6 servo amplifiers. 

 
1.1 Summary 

The MELSERVO-J4 series of multi-axis servo amplifiers inherits the high performance, sophisticated 
functions, and usability of the MR-J4-B servo amplifiers, and ensures space saving, reduced wiring, and 
energy saving. 
The MR-J4W_-B servo amplifier is connected to controllers, including a servo system controller, on the high-
speed synchronous network, SSCNET III/H. The servo amplifier directly receives a command from a 
controller to drive a servo motor. 
One MR-J4W_-B servo amplifier can drive two or three servo motors. The footprint of one MR-J4W_-B servo 
amplifier is considerably smaller than that of two or three MR-J4-B servo amplifiers. You can install MR-
J4W_-B servo amplifiers without clearance between them. This makes your system more compact. 
The multi-axis structure enables multiple axes to share the SSCNET III cable, control circuit power supply 
cable, and main circuit power supply cable. This ensures reduced wiring. 
For the MR-J4W_-B servo amplifier, the parameter settings allows you to use a rotary servo motor, linear 
servo motor, and direct drive motor for each axis. The axes can be connected to a rotary servo motor, linear 
servo motor, and direct drive motor, which have different capacity. Using a linear servo motor or direct drive 
motor simplifies the system, and using the MR-J4W_-B servo amplifier downsizes the equipment, enhances 
the equipment performance, and ensures space saving. 
Using regenerative energy generated when a servo motor decelerates ensures energy saving. 
Depending on the operating conditions, the regenerative option is not required. 
As the MR-J4-B servo amplifier, the MR-J4W_-B servo amplifier supports the one-touch tuning and the real-
time auto tuning. This enables you to easily adjust the servo gain according to the machine.  
The tough drive function and the drive recorder function, which are well-received in the MELSERVO-JN 
series, have been improved. The MR-J4W_-B servo amplifier supports the improved functions.  Additionally, 
the preventive maintenance support function detects an error in the machine parts. This function provides 
strong support for the machine maintenance and inspection. 
On the SSCNET III/H network, the stations are connected with a maximum distance of 100 m between them. 
This allows you to create a large system. 
The MR-J4W_-B servo amplifier supports the STO (Safe Torque Off) function. When the servo amplifier is 
connected to a SSCNET III/H-compatible servo system controller, in addition to the STO function, the servo 
amplifier also supports the SS1 (Safe Stop 1), SS2 (Safe Stop 2), SOS (Safe Operating Stop), SLS (Safely-
Limited Speed), SBC (Safe Brake Control) and SSM (Safe Speed Monitor) functions. 
The servo amplifier has a USB communication interface. Therefore, you can connect the servo amplifier to 
the personal computer with MR Configurator2 installed to perform the parameter setting, test operation, gain 
adjustment, and others. 
 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Fender Bassman Bassman 100 Owner'S Manual preview
Bassman Bassman 100
Brand: Fender Pages: 20
Fender Amp B-DEC 30 Owner'S Manual preview
Amp B-DEC 30
Brand: Fender Pages: 156
Fender G-DEC 3 Thirty & Fifteen Quick Start Manual preview
G-DEC 3 Thirty & Fifteen
Brand: Fender Pages: 24
QUAD II Classic Quad Electroacoustics Ltd, Iag House, Owner'S Manual preview
II Classic
Brand: QUAD Pages: 4
QSC ISA 280 Technical & Service Manual preview
ISA 280
Brand: QSC Pages: 142
Laney PB 150 HEAD User Manual preview
PB 150 HEAD
Brand: Laney Pages: 4
Channel Master CM-3410 Installation Instructions preview
CM-3410
Brand: Channel Master Pages: 2
McIntosh MX136 Service Manual preview
MX136
Brand: McIntosh Pages: 55
Acoustic Image Clarus 2R Owner'S Manual preview
Clarus 2R
Brand: Acoustic Image Pages: 8
ORANGE Crush PiX 20L Owner'S Manual preview
Crush PiX 20L
Brand: ORANGE Pages: 13
JBL BPX500.1 Service Manual preview
BPX500.1
Brand: JBL Pages: 31
J&M MA-967 Installation Instructions preview
MA-967
Brand: J&M Pages: 3
APART REVAMP1680 Instruction Manual preview
REVAMP1680
Brand: APART Pages: 16
Ampetronic ILD100 Handbook preview
ILD100
Brand: Ampetronic Pages: 12
Crown Macro-Tech MA-3600VZ Operation Manual preview
Macro-Tech MA-3600VZ
Brand: Crown Pages: 28
Lenz Digital Plus LZV100 Information Manual preview
Digital Plus LZV100
Brand: Lenz Pages: 16
icon Audio MB 845 Instruction Manual preview
MB 845
Brand: icon Audio Pages: 9
A SYSTEMS SR703 User Manual preview
SR703
Brand: A SYSTEMS Pages: 16

Brands by name

Popular brands

Load more brands