Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 186 / 588

background image

7. SPECIAL ADJUSTMENT FUNCTIONS

7 - 5

7.1.2 Adaptive filter II

POINT

The machine resonance frequency which adaptive filter II (adaptive tuning) can
respond to is about 100 Hz to 2.25 kHz. As for the resonance frequency out of
the range, set manually.
When adaptive tuning is executed, vibration sound increases as an excitation
signal is forcibly applied for several seconds.
When adaptive tuning is executed, machine resonance is detected for a
maximum of 10 seconds and a filter is generated. After filter generation, the
adaptive tuning mode automatically shifts to the manual setting.
Adaptive tuning generates the optimum filter with the currently set control gains.
If vibration occurs when the response setting is increased, execute adaptive
tuning again.
During adaptive tuning, a filter having the best notch depth at the set control
gain is generated. To allow a filter margin against machine resonance, increase
the notch depth in the manual setting.
Adaptive vibration suppression control may provide no effect on a mechanical
system which has complex resonance characteristics.
Adaptive tuning in the high accuracy mode is available with servo amplifiers with
software version C5 or later. The frequency is estimated more accurately in the
high accuracy mode compared to the standard mode. However, the tuning
sound may be larger in the high accuracy mode.

(1) Function

Adaptive filter II (adaptive tuning) is a function in which the servo amplifier detects machine vibration for
a predetermined period of time and sets the filter characteristics automatically to suppress mechanical
system vibration. Since the filter characteristics (frequency, depth) are set automatically, you need not
be conscious of the resonance frequency of a mechanical system.

R

e

spons

e of

mechanical system

No

tch

depth

Machine resonance point

Notch frequency

Frequency

Frequency

R

e

spons

e of

mechanical system

No

tch

depth

Machine resonance point

Notch frequency

Frequency

Frequency

When machine resonance is large and

frequency is low

When machine resonance is small and

frequency is high

«
...
184
185
186
187
188
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: QUAD Pages: 16

Brand: LABTEC Pages: 12

Brand: Omega Engineering Pages: 2

Brand: NAD Pages: 16

Brand: NAD Pages: 2

Brand: D.A.S. Pages: 15

Brand: Advance acoustic Pages: 18

Brand: Broadcast Tools Pages: 5

Brand: DigiTech Pages: 8

Brand: icon Audio Pages: 4

Brand: Musway Pages: 36

Brand: NAD Pages: 12

Brand: Tekbox Pages: 10

Brand: JBL Pages: 8

Brand: NAD Pages: 33

Brand: Renishaw Pages: 69

Brand: R.V.R. Elettronica Pages: 79

Brand: B2 Audio Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands