manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

1. FUNCTIONS AND CONFIGURATION 

1 -  7 

 

Model MR-J4W3- 

222B 

444B 

Functional safety 

 

 

STO (IEC/EN 61800-5-2) (Note 6) 

 

Safety 
performance 

Standards certified by 
CB (Note 10) 

EN ISO 13849-1 Category 3 PL e, IEC 61508 SIL 3, EN 62061 SIL CL3, EN 61800-5-2 

Response 
performance 

 

8 ms or less (STO input off 

→

 energy shut off) 

 

Test pulse input (STO) 
(Note 5) 

 

Test pulse interval: 1 Hz to 25 Hz 

Test pulse off time: Up to 1 ms 

 

Mean time to 
dangerous failure 
(MTTFd) 

MTTFd 

≥

 100 [years] (314a) 

Diagnosis converge 
(DC) 

DC = Medium, 97.6 [%] 

Average probability of 
dangerous failures 
per hour (PFH) 

6.4 × 10

-9

 [1/h] 

Compliance 
with global 
standards 

CE marking 

LVD: EN 61800-5-1 

EMC: EN 61800-3 

MD: EN ISO 13849-1, EN 61800-5-2, EN 62061 

UL standard 

 

UL 508C 

Structure (IP rating) 

 

Force cooling, open (IP20) 

Close mounting 

 

Possible 

 

Ambient 
temperature 

Operation 

0 °C to 55 °C (non-freezing) 

 

Storage 

-20 °C to 65 °C (non-freezing) 

Environment 

Ambient 
humidity 

Operation 

5 %RH to 90 %RH (non-condensing) 

Storage 

Ambience 

 

Indoors (no direct sunlight), free from corrosive gas, flammable gas, oil mist, dust, and dirt 

 

Altitude 

 

2000 m or less above sea level (Note 11) 

 Vibration 

  5.9 

m/s

2

 or less at 10 Hz to 55 Hz (directions of X, Y and Z axes) 

Mass  

[kg] 

1.9 

 

Note   1.  0.45 A is the value applicable when all I/O signals are used. The current capacity can be decreased by reducing the number of 

I/O points. 

 

  2.  Reusable regenerative energy corresponds to energy generated under the following conditions. 

Rotary servo motor: Regenerative energy is generated when the machine, whose moment of inertia is equivalent to the 
permissible charging amount, decelerates from the rated speed to stop. 
Linear servo motor: Regenerative energy is generated when the machine, whose mass is  equivalent to the permissible 

charging amount, decelerates from the maximum speed to stop. 

Direct drive motor: Regenerative energy is generated when the machine, whose moment of inertia is equivalent to the 

permissible charging amount, decelerates from the rated speed to stop. 

 

  3.  Moment of inertia when the machine decelerates from the rated speed to stop  

Moment of inertia for three axes when three motors decelerate simultaneously  
Moment of inertia for each axis when multiple motors do not decelerate simultaneously  
The values also apply to the direct drive motor. 

 

  4.  Mass when the machine decelerates from the maximum speed to stop  

The primary-side (coil) mass is included.  
Mass for three axes when three motors decelerate simultaneously  
Mass for each axis when multiple motors do not decelerate simultaneously 

 

  5.  Test pulse is a signal which instantaneously turns off a signal to the servo amplifier at a constant period for external circuit to 

self-diagnose. 

 

  6.  STO is common for all axes. 

 

  7.  The command communication cycle depends on the controller specifications and the number of axes connected. 

 

  8.  Servo amplifier with software version A3 or later is compatible with the command communication cycle of 0.222 ms. However, 

note that the following functions are not available when 0.222 ms is used: auto tuning (real time, one-touch, and vibration 
suppression control), adaptive filter II, vibration tough drive, and power monitoring. 

 

  9.  This value is applicable when a 3-phase power supply is used. 

 

10.  The safety level depends on the setting value of [Pr. PF18 STO diagnosis error detection time] and whether STO input 

diagnosis by TOFB output is performed or not. For details, refer to the Function column of [Pr. PF18] in section 5.2.6. 

 

11.  Follow the restrictions in section 2.7 when using this product at altitude exceeding 1000 m and up to 2000 m above sea level. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

K-array KA40 User Manual preview
KA40
Brand: K-array Pages: 8
K&M Analog Designs LTD Owner'S Manual preview
LTD
Brand: K&M Analog Designs Pages: 10
K&K Sound ULTRAPURE Product Manual preview
ULTRAPURE
Brand: K&K Sound Pages: 4
IMG STAGE LINE STA-2200 Instruction Manual preview
STA-2200
Brand: IMG STAGE LINE Pages: 18
DUB Edition DUBa1450 Installation And Operation Manual preview
DUBa1450
Brand: DUB Edition Pages: 18
Electro-Voice 7300A Brochure & Specs preview
7300A
Brand: Electro-Voice Pages: 4
Analog Devices SSM2304 Series Manual preview
SSM2304 Series
Brand: Analog Devices Pages: 20
Altec Lansing 1783 SIGNAL PROCESSING Manual preview
1783 SIGNAL PROCESSING
Brand: Altec Lansing Pages: 9
AudioControl LC-1.800 Quick Start Manual preview
LC-1.800
Brand: AudioControl Pages: 12
MadBoy F-LOUD 225 User Manual preview
F-LOUD 225
Brand: MadBoy Pages: 6
Soundstream USA 305 Owner'S Manual And Installation Manual preview
USA 305
Brand: Soundstream Pages: 10
Technics SU-9070 (X) Service Manual preview
SU-9070 (X)
Brand: Technics Pages: 19
AXTON A1390 Installation & Operating Instructions Manual preview
A1390
Brand: AXTON Pages: 58
Ametek CBA-1G-030B Operation Manual preview
CBA-1G-030B
Brand: Ametek Pages: 36
Somogyi Elektronic SAL MPA 120BT Instruction Manual preview
SAL MPA 120BT
Brand: Somogyi Elektronic Pages: 20
Audio Note M Zero Owner'S Manual preview
M Zero
Brand: Audio Note Pages: 5
Kustom Sienna 16 Owner'S Manual preview
Sienna 16
Brand: Kustom Pages: 12
Nakamichi PA-5 Service Manual preview
PA-5
Brand: Nakamichi Pages: 15

Brands by name

Popular brands

Load more brands