Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 274 / 588

background image

11. OPTIONS AND PERIPHERAL EQUIPMENT

11 - 29

11.6 Molded-case circuit breakers, fuses, magnetic contactors

Always use one molded-case circuit breaker and one magnetic contactor with one servo amplifier. When
using a fuse instead of the molded-case circuit breaker, use the one having the specifications given in this
section.
When using a combination of the rotary servo motor, linear servo motor, or direct drive motor, select a
molded-case circuit breaker, a fuse or a magnetic contactor tentatively, assuming one type of the servo
motors are used for two or three axes. After the tentative selections are made for all types of the servo
motors, use the largest among all molded-case circuit breakers, fuses, or magnetic contactors.

(1) For main circuit power supply

CAUTION

To prevent the servo amplifier from smoke and a fire, select a molded-case circuit
breaker which shuts off with high speed.
Always use one molded-case circuit breaker and one magnetic contactor with one
servo amplifier.

(a) For MR-J4W2

Total output of

rotary servo

motors

Total

continuous

thrust of linear

servo motors

Total output of

direct drive

motors

Molded-case circuit breaker

(Note 5, 6)

Fuse

(Note 2)

Magnetic
contactor

Frame, rated current

Voltage

AC

[V]

(Note 1)

Class

Current

[A]

Voltage

AC

[V]

300 W or less

50 A frame 5 A

(Note 3)

240 T

15

300

S-N10

S-T10

From over 300
W to 600 W

150 N or less

100 W or less

50 A frame 10 A

(Note 3)

20

From over 600
W to 1 kW

From over 150
N to 300 N

From over 100
W to 252 W

50 A frame 15 A

(Note 3)

20

From over 1
kW to 2 kW

From over 300
N to 720 N

From over 252
W to 838 W

50 A frame 20 A

(Note 3)

30

S-N20

(Note 4)

S-T21

Note 1. When using the servo amplifier as an EC/EN/UL/CSA standard compliant product, refer to app. 4.

2. Use a magnetic contactor with an operation delay time (interval between current being applied to the coil until

closure of contacts) of 80 ms or less.

3. When not using the servo amplifier as an EC/EN/UL/CSA standard compliant product, molded-case circuit breaker

of 30 A frame can be used.

4. S-N18 can be used when auxiliary contact is not required.

5.

A molded-case circuit breaker will not change to select regardless of use of a power factor improving AC reactor.

6. Use a molded-case circuit breaker having the operation characteristics equal to or higher than Mitsubishi Electric

general-purpose products.

«
...
272
273
274
275
276
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: Zenith Pages: 8

Brand: Fairchild Pages: 8

Brand: Fenton Pages: 16

Brand: Korg Pages: 31

Brand: Teac Pages: 60

Brand: PS Audio Pages: 28

Brand: PowerBass Pages: 24

Brand: Sherwood Pages: 14

Brand: M-system Pages: 2

Brand: Harman Kardon Pages: 50

dPatch SutterPatch

Brand: Sutter Instrument Pages: 2

Jazz Chorus JC-90

Brand: Roland Pages: 10

Brand: DAPAudio Pages: 24

Brand: Altimium Pages: 36

The Nocturne AX20

Brand: Harman Kardon Pages: 16

Brand: Myryad Pages: 8

Brand: Harman Kardon Pages: 12

Stereo 60 MK III M

Brand: icon Audio Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands