Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 384 / 588

background image

16. FULLY CLOSED LOOP SYSTEM

16 - 19

16.3.4 Fully closed loop control error detection functions

If fully closed loop control becomes unstable for some reason, the speed at servo motor side may increase
abnormally. The fully closed loop control error detection function is a protective function designed to pre-
detect it and stop operation.
The fully closed loop control error detection function has two different detection methods, speed deviation
and position deviation, and errors are detected only when the corresponding functions are enabled by setting
[Pr. PE03 Fully closed loop function selection 2].
The detection level setting can be changed using [Pr. PE06] and [Pr. PE07].

(1) Parameter

Select the fully closed loop control error detection function.

Fully closed loop control error detection function
0: Disabled
1: Speed deviation error detection
2: Position deviation error detection
3: Speed deviation error, position deviation error detection
(Initial value)

[Pr. PE03]

(2) Fully closed loop control error detection functions

Servo motor

Linear encoder

1) Servo motor-side feedback speed [r/min]
2) Servo motor-side feedback position [pulse]

(load side equivalent value)

3) Load-side feedback speed [r/min]
4) Load-side feedback position [pulse]

(a) Speed deviation error detection

Set [Pr. PE03] to "_ _ _ 1" to enable the speed deviation error detection.

Speed deviation error detection

1

[Pr. PE03]

The function compares the servo motor-side feedback speed (1)) and load-side feedback speed (3)).
If the deviation is not less than the set value (1 r/min to the permissible speed) of [Pr. PE06 Fully
closed loop control speed deviation error detection level], the function generates [AL. 42.2 Servo
control error by speed deviation] and stops. The initial value of [Pr. PE06] is 400 r/min. Change the
set value as required.

«
...
382
383
384
385
386
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: NAD Pages: 2

Brand: E&I Pages: 13

PowerLight Series

Brand: QSC Pages: 100

Brand: SMSL Pages: 28

Brand: Madison Pages: 51

Brand: Advance acoustic Pages: 11

Brand: Pronomic Pages: 16

Brand: Technalogix Pages: 63

Brand: CyberData Pages: 3

Lightstar Direct

Brand: Carver Pages: 20

Brand: Teac Pages: 96

Brand: Sonic Frontiers Pages: 8

Tone Beast TB12

Brand: Warm Audio Pages: 2

Brand: Goldmund Pages: 14

Brand: Mark Levinson Pages: 20

Brand: Crest Audio Pages: 2

Brand: Lombardi Pages: 10

Brand: Cloud Pages: 7

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands