Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 386 / 588

background image

16. FULLY CLOSED LOOP SYSTEM

16 - 21

16.3.8 Absolute position detection system under fully closed loop system

An absolute type linear encoder is necessary to configure an absolute position detection system under fully
closed loop control using a linear encoder. In this case, the encoder battery need not be installed to the
servo amplifier. When an rotary encoder is used, an absolute position detection system can be configured by
installing the encoder battery to the servo amplifier. In this case, the battery life will be shorter because the
power consumption is increased as the power is supplied to the two encoders of motor side and load side.
For the absolute position detection system with linear encoder, the restrictions mentioned in this section
apply. Enable the absolute position detection system with [Pr. PA03 Absolute position detection system] and
use this servo within the following restrictions.

(1) Using conditions

(a) Use an absolute type linear encoder with the load-side encoder.

(b) Select Always fully closed loop ([Pr. PA01] = _ _ 1 _ and [Pr. PE01] = _ _ _ 0).

(2) Absolute position detection range using encoder

Encoder type

Absolute position detection enabled range

Linear encoder
(Serial Interface)

Movable distance range of linear encoder (within 32-bit absolute position data)

(3) Alarm detection

The absolute position-related alarm ([AL. 25]) and warnings (AL. 92] and [AL. 9F]) are not detected.

«
...
384
385
386
387
388
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: QUAD Pages: 12

Brand: NAD Pages: 2

MINAS-BL GP series

Brand: Panasonic Pages: 56

Brand: Bad Cat Pages: 7

Brand: Pangea Pages: 7

Brand: T-audio Pages: 13

Brand: Fuba Pages: 19

Brand: E&I Pages: 16

Brand: Ericsson Pages: 34

iPaul BPM 245.000

Brand: Rainbow Pages: 16

Brand: Denon Pages: 12

Brand: Nady Audio Pages: 8

Brand: Cloud Pages: 7

Brand: Marshall Electronics Pages: 1

Sonic Frontiers SFS-40

Brand: Sonic Frontiers Pages: 6

Brand: Texas Instruments Pages: 13

Brand: Bugera Pages: 10

Brand: ELCART Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands