manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

17. APPLICATION OF FUNCTIONS 

17 -  37 

 

Display 

Name 

Error detail 

Corrective action example 

C006 

Amplifier command start 
error 

One-touch tuning was attempted to start in 
the amplifier command method under the 
following speed condition. 
Servo motor speed of one axis.: 20 r/min or 
higher 

Execute the one-touch tuning in the amplifier 
command method while the servo motor is 
stopped.  

C007 Amplifier 

command 

generation error 

1.  One-touch tuning was executed in the 

amplifier command method when the 
permissible travel distance is set to 100 
pulses or less in the encoder pulse unit, or 
the distance is set not to increase the 
servo motor speed to 150 r/min (mm/s) (50 
r/min for direct drive motor) or higher at the 
time of load to motor inertia ratio 
estimation. 

Set a permissible travel distance to 100 
pulses or more in the encoder pulse unit, or a 
distance so as to increase the servo motor 
speed to 150 r/min (mm/s) (50 r/min for direct 
drive motor) or higher at the time of load to 
motor inertia ratio estimation, and then 
execute the one-touch tuning. Set a 
permissible travel distance to four or more 
revolutions as a guide value. 
Load to motor inertia ratio will be estimated 
when "0000" or "0001" is set in [Pr. PA08 
Auto tuning mode] at the start of one-touch 
tuning. 
If the permissible travel distance is short and 
the servo motor speed cannot be increased to 
150 r/min (mm/s) (50 r/min for direct drive 
motor) or higher, select "Auto tuning mode 2 
(_ _ _ 2)", "Manual mode (_ _ _ 3)", or "2 gain 
adjustment mode 2 (_ _ _ 4)" of "Gain 
adjustment mode selection" in [Pr. PA08]. 

 

 

2.  An overspeed alarm detection level is set 

so that the servo motor speed becomes 
150 r/min (mm/s) (50 r/min for direct drive 
motor) or less at the time of load to motor 
inertia ratio estimation. 

When estimating the load to motor inertia 
ratio, set the overspeed alarm detection level 
so that the speed becomes 150 r/min or 
more. 

 

 

3.  The torque limit has been set to 0. 

Set the torque limit value to greater than 0. 

C008 

Stop signal 

EM2 was turned off during one-touch tuning in 
the amplifier command method. 

Review the one-touch tuning start position 
and permissible travel distance for the 
amplifier command method. 
After ensuring safety, turn on EM2. 

C009 

Parameter 

Parameters for manufacturer setting have 
been changed. 

Return the parameters for manufacturer 
setting to the initial values. 

C00A 

Alarm 

One-touch tuning was attempted to start in 
the amplifier command method during alarm 
or warning. 
Alarm or warning occurred during one-touch 
tuning by the amplifier command method. 

Start one-touch tuning when no alarm or 
warning occurs. 
Prevent alarm or warning from occurring 
during one-touch tuning. 

C00F One-touch 

tuning 

disabled 

"One-touch tuning function selection" in [Pr. 
PX13] is "Disabled (_ _ _ 0)". 

Select "Enabled (_ _ _ 1)". 

 

6)  If an alarm occurs 

If an alarm occurs during the one-touch tuning, the tuning will be forcibly terminated. Remove the 
cause of the alarm and execute one-touch tuning again. When executing one-touch tuning in the 
amplifier command method again, return the moving part to the tuning start position. 

 

7)  If a warning occurs 

If a warning which continues the motor driving occurs during one-touch tuning by the user 
command method, the tuning will be continued. If a warning which does not continue the motor 
driving occurs during the tuning, one-touch tuning will be stopped. 
One-touch tuning will be stopped when warning occurs during one-touch tuning by the amplifier 
command method regardless of the warning type. Remove the cause of the warning, and return 
the moving part to the tuning start position. Then, execute the tuning again. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Jensen A1000 Owner'S Manual And Installation Instructions preview
A1000
Brand: Jensen Pages: 6
AAVIK M-380 User Manual preview
M-380
Brand: AAVIK Pages: 8
Arcam ALPHA AV50 Handbook preview
ALPHA AV50
Brand: Arcam Pages: 15
Prolude Amplification KO750 User Manual preview
KO750
Brand: Prolude Amplification Pages: 15
Electro-Voice CP-Series Power Amps CP1800 Owner'S Manual preview
CP-Series Power Amps CP1800
Brand: Electro-Voice Pages: 36
Korg A4 Guitar Owner'S Manual preview
A4 Guitar
Brand: Korg Pages: 31
NJS NJS401 Manual preview
NJS401
Brand: NJS Pages: 8
SAL MPA 120BT Instruction Manual preview
MPA 120BT
Brand: SAL Pages: 40
Crest Audio CPX 4 Operating Manual preview
CPX 4
Brand: Crest Audio Pages: 18
XTA DS800 Operator'S Manual preview
DS800
Brand: XTA Pages: 14
Parallel Audio MA4200 Operation Manual preview
MA4200
Brand: Parallel Audio Pages: 12
Laney IronHeart IRT120H Instructions Manual preview
IronHeart IRT120H
Brand: Laney Pages: 20
Shure UA834WB Quick Start Manual preview
UA834WB
Brand: Shure Pages: 4
Harris AM-7224/URC Technical Manual preview
AM-7224/URC
Brand: Harris Pages: 128
Extron electronics HPA 1001-70V Specifications preview
HPA 1001-70V
Brand: Extron electronics Pages: 4
Gold Note PH-10 User Manual preview
PH-10
Brand: Gold Note Pages: 52
Soundigital 1 200.2 EVO5 User Manual preview
1 200.2 EVO5
Brand: Soundigital Pages: 14
VAC Musicbloc Master 300 iQ Operation & Maintenance Information preview
Musicbloc Master 300 iQ
Brand: VAC Pages: 18

Brands by name

Popular brands

Load more brands