Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 525 / 588

background image

APPENDIX

App. - 10

App. 4.2.4 General cautions for safety protection and protective measures

Observe the following items to ensure proper use of the MR-J4 servo amplifiers.

(1) For safety components and installing systems, only qualified personnel and professional engineers

should perform.

(2) When mounting, installing, and using the MELSERVO MR-J4 servo amplifier, always observe standards

and directives applicable in the country.

(3) The item about noises of the test notices in the manuals should be observed.

App. 4.2.5 Residual risk

(1)  Be sure that all safety related switches, relays, sensors, etc., meet the required safety standards.

(2)  Perform all risk assessments and safety level certification to the machine or the system as a whole.

(3)  If the upper and lower power modules in the servo amplifier are shorted and damaged simultaneously,

the servo motor may make a half revolution at a maximum.

(4) Only qualified personnel are authorized to install, start-up, repair or service the machines in which these

components are installed. Only trained engineers should install and operate the equipment. (ISO 13849-
1 Table F.1 No. 5)

(5) Separate the wiring for safety observation function from other signal wirings. (ISO 13849-1 Table F.1 No.

1)

(6) Protect the cables with appropriate ways (routing them in a cabinet, using a cable guard, etc.).

(7) Keep the required clearance/creepage distance depending on voltage you use.

App. 4.2.6 Disposal

Disposal of unusable or irreparable devices should always occur in accordance with the applicable country-
specific waste disposal regulations. (Example: European Waste 16 02 14)

App. 4.2.7 Lithium battery transportation

To transport lithium batteries, take actions to comply with the instructions and regulations such as the United
Nations (UN), the International Civil Aviation Organization (ICAO), and the International Maritime
Organization (IMO).
The batteries (MR-BAT6V1SET, MR-BAT6V1SET-A, MR-BAT6V1, and MR-BAT6V1BJ) are assembled
batteries from two batteries (lithium metal battery CR17335A) which are not subject to the dangerous goods
(Class 9) of the UN Recommendations.

«
...
523
524
525
526
527
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: NAD Pages: 2

Brand: NAD Pages: 2

Brand: B&K Pages: 24

Brand: NAD Pages: 3

Brand: NAD Pages: 26

Brand: Maintronic Pages: 4

Brand: B&K Pages: 15

VIBRO-KING P/N 053493

Brand: Fender Pages: 8

Brand: Korg Pages: 34

Brand: Monacor Pages: 15

Brand: Total Mobile Audio Pages: 11

Brand: Velleman-Kit Pages: 24

Brand: Laney Pages: 16

Brand: Tascam Pages: 12

Brand: Altec Lansing Pages: 4

Brand: JET CITY AMPLIFICATION Pages: 18

Bassman Bassman 100

Brand: Fender Pages: 16

Brand: Advance Paris Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands