manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

APPENDIX 

App. -  22 

 
App. 5.3 Cautions 

The following basic safety notes must be read carefully and fully in order to prevent injury to persons or 
damage to property. 
Only qualified personnel are authorized to install, start-up, repair or service the machines in which these 
components are installed. 
They must be familiar with all applicable local safety regulations and laws in which machines with these 
components are installed, particularly the standards and guidelines mentioned in this Instruction Manual and 
the requirements mentioned in ISO/EN ISO 13849-1, IEC 61508, IEC/EN 61800-5-2, and IEC/EN 60204-1. 
The staff responsible for this work must be given express permission from the company to perform start-up, 
programming, configuration, and maintenance of the machine in accordance with the safety standards. 
 

WARNING 

Improper installation of the safety related components or systems may cause 
improper operation in which safety is not assured, and may result in severe 
injuries or even death. 

 
Protective Measures 

As described in IEC/EN 61800-5-2, the Safe Torque Off (STO) function only prevents the MFR-J4 series 
servo amplifier from supplying energy to the servo motor. Therefore, if an external force acts upon the 
drive axis, additional safety measures, such as brakes or counter-weights must be used. 

 
App. 5.4 Residual risk 

Machine manufacturers are responsible for all risk evaluations and all associated residual risks. Below are 
residual risks associated with the STO/EMG function. Mitsubishi Electric is not liable for any damages or 
injuries caused by the residual risks. 
 
(1)  The SS1 function only guarantees the delay time before STO/EMG is engaged. Proper setting of this 

delay time is the full responsibility of the company and/or individuals responsible for installation and 
commissioning of the safety related system. The system, as a whole, must pass safety standards 
certification. 

 
(2)  When the SS1 delay time is shorter than the required servo motor deceleration time, if the forced stop 

function is malfunctioning, or if STO/EMG is engaged while the servo motor is still rotating; the servo 
motor will stop with the dynamic brake or freewheeling. 

 
(3)  For proper installation, wiring, and adjustment, thoroughly read the manual of each individual safety 

related component. 

 
(4)  Be sure that all safety related switches, relays, sensors, etc., meet the required safety standards. 

The Mitsubishi Electric safety related components mentioned in this manual are certified by Certification 
Body as meeting the requirements of ISO/EN ISO 13849-1 Category 3, PL d and IEC 61508 SIL 2. 

 
(5)  Safety is not assured until safety-related components of the system are completely installed or adjusted. 
 
(6)  When replacing a servo amplifier etc. or MR-J3-D05, confirm that the new equipment is exactly the 

same as those being replaced. Once installed, be sure to verify the performance of the functions before 
commissioning the system. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

R&R Ampflication DP-13 Manual preview
DP-13
Brand: R&R Ampflication Pages: 16
Tabor Electronics 9260 User Manual preview
9260
Brand: Tabor Electronics Pages: 38
t.amp TSA 4-700 Owner'S Manual preview
TSA 4-700
Brand: t.amp Pages: 12
t.a.c. V-88 Instructions For Use Manual preview
V-88
Brand: t.a.c. Pages: 64
OSEE BDA6801N User Manual preview
BDA6801N
Brand: OSEE Pages: 12
Lanzar MXA224 Owner'S Manual preview
MXA224
Brand: Lanzar Pages: 13
Jolida JD 502CRC Owner'S Manual preview
JD 502CRC
Brand: Jolida Pages: 17
ZENEC ZE-5.1D Operation Manual preview
ZE-5.1D
Brand: ZENEC Pages: 30
JBL Synthesis S400 User Manual preview
Synthesis S400
Brand: JBL Pages: 22
Surpass SP-150MB User Manual preview
SP-150MB
Brand: Surpass Pages: 14
Crown XLC2500 Operation Manual preview
XLC2500
Brand: Crown Pages: 32
Sansui AU-G55X Service Manual preview
AU-G55X
Brand: Sansui Pages: 15
Trinity SILVER REFERENCE Manual preview
SILVER REFERENCE
Brand: Trinity Pages: 22
Kramer VM-4HDMI User Manual preview
VM-4HDMI
Brand: Kramer Pages: 13
Harman JBL Commercial VMA Series Operation Manual preview
JBL Commercial VMA Series
Brand: Harman Pages: 28
Kramer PT-101R User Manual preview
PT-101R
Brand: Kramer Pages: 6
Cyrus 6a User Instructions preview
6a
Brand: Cyrus Pages: 25
Forney IDD-II Manual preview
IDD-II
Brand: Forney Pages: 18

Brands by name

Popular brands

Load more brands