manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

APPENDIX 

App. -  55 

 

Data type 

Description 

Home position [command unit] 

The home position is displayed. 

Main circuit bus voltage 

The voltage of main circuit converter (between P+ and N-) is displayed. 

Regenerative load ratio 

The ratio of regenerative power to permissible regenerative power is displayed in %. 

Effective load ratio 

The continuous effective load current is displayed. 
The effective value is displayed considering a rated current as 100%. 

Peak load ratio 

The maximum torque generated is displayed. 
The highest value in the past 15 s is displayed, with the rated torque being 100 %. 

Estimate inertia moment ratio 

The set ratio of the load inertia moment to the servo motor shaft inertia moment is 
displayed. 

Model loop gain 

The model loop gain value is displayed. 

LED display 

The value shown on the 7-segment LED display of the servo amplifier is displayed. 

Load-side encoder information 1 

When an incremental type linear encoder is used for the load-side encoder, the Z-phase 
counter of the load-side encoder is displayed by encoder pulses. 
When an absolute position type linear encoder is used for the load-side encoder, the 
encoder absolute position is displayed. 

Load-side encoder information 2 

When an incremental type linear encoder is used for the load-side encoder, the display 
shows 0. 
When an absolute position type linear encoder is used for the load-side encoder, the 
display shows 0. 
When a rotary encoder is used for the load-side encoder, the display shows the multi-
revolution counter value of the encoder. 

Speed feedback 

The servo motor speed is displayed. 

Servo motor thermistor temperature 

The thermistor temperature is displayed for the servo motor with a thermistor. 
For the servo motor without thermistor, "9999" is displayed. 
For the servo motor with a thermistor, refer to each servo motor instruction manual. 

Z-phase counter 

The Z-phase counter is displayed in the encoder pulse unit. 
For an incremental type linear encoder, the Z-phase counter is displayed. The value is 
counted up from 0 based on the home position (reference mark). 
For an absolute position type linear encoder, the encoder absolute position is displayed. 

Module power consumption  

The module power consumption is displayed. 
The positive value is displayed in power running. The negative value is displayed in 
regeneration. 

Module integral power consumption 

The module integral power consumption is displayed. 

Disturbance torque 

The difference between the torque necessary to drive the servo motor and the actually 
required torque (Torque current value) is displayed as the disturbance torque. 

Instantaneous torque 

The instantaneous torque is displayed. 
The value of torque being occurred is displayed in real time considering a rated torque as 
100%. 

Overload alarm margin 

The margins to the levels which trigger [AL. 50 Overload 1] and [AL. 51 Overload 2] are 
displayed in percentage. 

Error excessive alarm margin 

The margin to the level which triggers the error excessive alarm is displayed in units of 
encoder pulses. 
The error excessive alarm occurs at 0 pulses. 

Settling time 

The time (Settling time) after command is completed until INP (In-position) turns on is 
displayed. 

Overshoot amount 

The overshoot amount during position control is displayed in units of encoder pulses. 

Servo motor side/load-side position 
deviation 

During fully closed loop control, a deviation between servo motor side position and load-
side position is displayed. 
The number of pulses displayed is in the load-side encoder pulse unit. 

Servo motor side/load-side speed 
deviation 

During fully closed loop control, a deviation between servo motor side speed and load-side 
speed is displayed. 

Internal temperature of encoder 

The internal temperature of encoder is displayed. "0" is displayed for the linear servo 
motor. When an encoder communication error occurs, the last value will be displayed 
before the error. 
This is available with servo amplifiers with software version C4 or later. 

Machine diagnostic status 

The current status of the machine diagnostic function is displayed. 

Friction estimation data 

The friction estimation data estimated by the machine diagnostic function is displayed. 

Vibration estimation data 

The vibration estimation data estimated by the machine diagnostic function is displayed. 

 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

PROEL TUBE100USB User Manual preview
TUBE100USB
Brand: PROEL Pages: 39
Vanguard Dynamics VAIL CAST Quick Start Manual preview
VAIL CAST
Brand: Vanguard Dynamics Pages: 3
DAPAudio Vision 1600 Manual preview
Vision 1600
Brand: DAPAudio Pages: 18
IMG STAGE LINE STA-2200 Instruction Manual preview
STA-2200
Brand: IMG STAGE LINE Pages: 18
Pyle Pro PPG860A Owner'S Manual preview
PPG860A
Brand: Pyle Pro Pages: 2
Klipsch ProMedia DD-5.1 User Manual preview
ProMedia DD-5.1
Brand: Klipsch Pages: 34
Bazooka Phat Tuesday MGA11000H Installation Manual preview
Phat Tuesday MGA11000H
Brand: Bazooka Pages: 60
Serene UA-50 Installation & Operation preview
UA-50
Brand: Serene Pages: 2
Art Pro VLA II User Manual preview
Pro VLA II
Brand: Art Pages: 16
Destination Audio SWA200 Installation & Operation Manual preview
SWA200
Brand: Destination Audio Pages: 12
Lint Audio KWELA TONES Assembly Instructions Manual preview
KWELA TONES
Brand: Lint Audio Pages: 32
Phonic ZA100 User Manual preview
ZA100
Brand: Phonic Pages: 24
DAPAudio PA90CDT Manual preview
PA90CDT
Brand: DAPAudio Pages: 18
Opengear ADA-8402-B User Manual preview
ADA-8402-B
Brand: Opengear Pages: 36
Fender 2300100000 Quick Start Manual preview
2300100000
Brand: Fender Pages: 12
Ashdown Guy Pratt INTERSTELLAR-600 User Manual preview
Guy Pratt INTERSTELLAR-600
Brand: Ashdown Pages: 27
Crest Audio P3500S Specifications preview
P3500S
Brand: Crest Audio Pages: 1
MIXHITS AUDIO MRT-B120D Operation Manual preview
MRT-B120D
Brand: MIXHITS AUDIO Pages: 14

Brands by name

Popular brands

Load more brands