manualshive.com logo in svg

Mitsubishi Electric MR-J4W2-0303B6, Instruction Manual

The Mitsubishi Electric MR-J4W2-0303B6 is a cutting-edge product designed to deliver precise and efficient performance. For users in need of guidance, an easy-to-understand Instruction Manual is available for free download at 88.208.23.73:8080. Unlock the full potential of this exceptional product with our comprehensive manual.

Share
Download
background image

APPENDIX 

App. -  56 

 

App. 15 STO function with SIL 3 certification 

The MR-J4 series general-purpose AC servo amplifiers now comply with safety integrity level 3 (SIL 3) of the 
IEC 61508:2010 functional safety standard. 
 
App. 15.1 Target models 

MR-J4 series AC servo amplifiers (excluding MR-J4-03A6(-RJ) and MR-J4W2-0303B6) 
 
App. 15.2 Change of the compliance 

The target MR-J4 servo amplifiers now comply with SIL 3 (Table app. 3). 
 

Table app. 3 Compliance with SIL 3 

 

Before change 

After change 

Safety performance 
(Standards certified by CB) 

EN ISO 13849-1 Category 3 PL d,  
IEC 61508 SIL 2,  
EN 62061 SIL CL 2,  
EN 61800-5-2 STO function 

EN ISO 13849-1 Category 3 PL e,  
IEC 61508 SIL 3,  
EN 62061 SIL CL 3,  
EN 61800-5-2 STO function 

 
App. 15.3 Schedule 

For the products manufactured in Japan, this change has been made sequentially from the June 2015 
production. 
For the products manufactured and sold in China, this change has been made sequentially from the 
December 2015 production. 
There may be cases where both the former and new products exist in the distribution stage. 
 
App. 15.4 Use with SIL 3 

Set the safety level with [Pr. PF18 STO diagnosis error detection time]. 
To use the servo amplifier with SIL 3, set [Pr. PF18 STO diagnosis error detection time] within the range of 1 
to 60, connect the TOFB output (CN8) of the servo amplifier to the input of a SIL 3-certified controller and 
execute the diagnosis. SIL 3 functional safety of the servo amplifiers is certified by TÜV SÜD. 
 
App. 15.5 Use with SIL 2 (as conventional) 

The servo amplifiers are still capable of SIL 2 as before regardless of whether the STO diagnosis function is 
enabled or not. 
Either of the conventionally-used TÜV Rheinland certification or the new TÜV SÜD certification may be 
used. 
 

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

NAD 114 Owner'S Manual preview
114
Brand: NAD Pages: 32
Accuphase E-213 Instruction Manual preview
E-213
Brand: Accuphase Pages: 50
Randall X2 Owner'S Manual preview
X2
Brand: Randall Pages: 9
Technics SU-G30 Owner'S Manual preview
SU-G30
Brand: Technics Pages: 100
Nobsound NS-13G Instructions preview
NS-13G
Brand: Nobsound Pages: 2
McIntosh MC257 Owner'S Manual preview
MC257
Brand: McIntosh Pages: 20
Linn LK240 Owner'S Manual preview
LK240
Brand: Linn Pages: 22
XTE Electronic Digital Technology XTDT3200 User Manual preview
Digital Technology XTDT3200
Brand: XTE Electronic Pages: 12
Pyramid Technical Consultants CP15AF User Manual preview
CP15AF
Brand: Pyramid Technical Consultants Pages: 33
Crown PZM-11LL Quick Reference preview
PZM-11LL
Brand: Crown Pages: 4
Revox Re: Source M51 Quick Start Manual preview
Re: Source M51
Brand: Revox Pages: 9
Phoenix Gold The One Limited Edition Amplifier Manual preview
The One Limited Edition Amplifier
Brand: Phoenix Gold Pages: 8
Fender Stage 1000 Service Manual preview
Stage 1000
Brand: Fender Pages: 23
Alpha Power ETO 91B User Manual preview
ETO 91B
Brand: Alpha Power Pages: 33
Harman Kardon HK6200 Technical Manual preview
HK6200
Brand: Harman Kardon Pages: 32
AkitikA GT-108 Assembly Manual preview
GT-108
Brand: AkitikA Pages: 56
Rotel RA-1210 Owner'S Manual preview
RA-1210
Brand: Rotel Pages: 5
AR 350S1G6A Series Operating And Service Manual preview
350S1G6A Series
Brand: AR Pages: 60

Brands by name

Popular brands

Load more brands