Mitsubishi Electric MR-J4W2-0303B6 Instruction Manual Download | Manualshive

Page: 91 / 588

background image

4. STARTUP

4 - 14

4.4 Test operation

Before starting actual operation, perform test operation to make sure that the machine operates normally.
Refer to section 4.2 for the power on and off methods of the servo amplifier.

POINT

If necessary, verify controller program by using motor-less operation. Refer to
section 4.5.2 for the motor-less operation.

Test operation of the servo motor

alone in JOG operation of test

operation mode

Test operation of the servo motor

alone by commands

Test operation with the servo motor

and machine connected

In this step, confirm that the servo amplifier and servo motor operate
normally. With the servo motor disconnected from the machine, use the test
operation mode and check whether the servo motor rotates correctly. Refer
to section 4.5 for the test operation mode.

In this step, confirm that the servo motor rotates correctly under the
commands from the controller.
Give a low speed command at first and check the rotation direction, etc. of
the servo motor. If the machine does not operate in the intended direction,
check the input signal.

In this step, connect the servo motor with the machine and confirm that the
machine operates normally under the commands from the controller.
Give a low speed command at first and check the operation direction, etc. of
the machine. If the machine does not operate in the intended direction,
check the input signal.
Check any problems with the servo motor speed, load ratio, and other status
display items with MR Configurator2.
Then, check automatic operation with the program of the controller.

4.5 Test operation mode

CAUTION

The test operation mode is designed for checking servo operation. It is not for
checking machine operation. Do not use this mode with the machine. Always use
the servo motor alone.
If the servo motor operates abnormally, use EM2 (Forced stop 2) to stop it.

POINT

The content described in this section indicates that the servo amplifier and a
personal computer are directly connected.

By using a personal computer and MR Configurator2, you can execute jog operation, positioning operation,
DO forced output program operation without connecting the servo system controller.

«
...
89
90
91
92
93
...
»

Summary of Contents for MR-J4W2-0303B6













































































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2-0303B6

Brand: Harman Kardon Pages: 8

Brand: NAD Pages: 20

Brand: NAD Pages: 8

Brand: TC Electronic Pages: 45

Brand: Gainlab Audio Pages: 15

Brand: NAIM Pages: 24

Brand: Anthem Pages: 3

Brand: JBL Pages: 13

Brand: lag Pages: 2

Brand: Creek Audio Pages: 2

Brand: Harman Kardon Pages: 11

Brand: Bob Carver Pages: 9

Brand: C.E.C. Pages: 15

Brand: Mark Acoustic Pages: 16

Brand: Bass Face Pages: 8

Brand: DB Drive Pages: 8

Brand: Audio Press Box Pages: 8

Brand: Marantz Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands