manualshive.com logo in svg

Mitsubishi Electric MR-J4W2, Instruction Manual

The Mitsubishi Electric MR-J4W2 Instruction Manual is a comprehensive guide for users looking to optimize their experience with this cutting-edge product. Easily downloadable from 88.208.23.73:8080, this manual provides step-by-step instructions, troubleshooting tips, and valuable insights, ensuring a hassle-free and efficient operation – all for free!

Share
Download
background image

5. PARAMETERS 

5 -  47 

 
5.2.5 Extension setting 2 parameters ([Pr. PE_ _ ]) 

No. 

Symbol 

Name and function 

Initial 
value 

[unit] 

Setting

 range 

Each/

Common

PE01  **FCT1  Fully closed loop function selection 1 

This parameter is not available with MR-J4W2-0303B6 servo amplifiers. 

Refer to Name 
and function 
column. 

Each 

  

 

Setting 

digit 

Explanation 

Initial 
value 

 

 

 

 

 

_ _ _ x 

Fully closed loop function selection 
0: Always enabled 
1: Switching with the control command of controller 

(switching semi./full.) 

0h    

 

 

 

 

 

 

Switching with the control 

command of controller 

Control system 

 

 

 

 

 

 

 

 

 

 

Off 

Semi closed loop control 

 

 

 

 

 

 

 

 

 

 

On 

Fully closed loop control 

 

 

 

 

 

 

 

 

 

 

To enable the digit, select "Fully closed loop control mode 
(_ _ 1 _)" of "operation mode selection" in [Pr. PA01]. 
When "Absolute position detection system" is "Enabled (_ _ 
_ 1)" in [Pr. PA03], setting "1" will trigger [AL. 37 Parameter 
error]. 
 

 

 

 

 

 

 

 

 

_ _ x _ 

For manufacturer setting 

0h 

 

 

 

 

 

 

 

_ x _ _ 

 

0h 

 

 

 

 

 

 

 

x _ _ _ 

 

0h 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

PE03 

*FCT2 

Fully closed loop function selection 2 
This parameter is not available with MR-J4W2-0303B6 servo amplifiers. 

Refer to Name 
and function 
column. 

Each 

  

 

Setting 

digit 

Explanation 

Initial 
value 

 

 

 

 

 

_ _ _ x 

Fully closed loop control error detection function selection 
0: Disabled 
1: Speed deviation error detection 
2: Position deviation error detection 
3: Speed deviation error/position deviation error detection 

3h    

 

 

 

 

 

_ _ x _ 

Position deviation error detection system selection 
0: Continuous detection system 
1: Detection system at stop (detected with command set to 

"0") 

0h    

 

 

 

 

 

_ x _ _ 

For manufacturer setting 

0h 

 

 

 

 

 

 

 

x _ _ _ 

Fully closed loop control error reset selection 
0: Reset disabled (reset by powering off/on enabled) 
1: Reset enabled 

0h    

 

 

 

 

 

 

 

 

 

 

 

 

PE04 

**FBN 

Fully closed loop control - Feedback pulse electronic gear 1 - Numerator 
Set a numerator of electronic gear for the servo motor encoder pulse at the fully 
closed loop control. 
Set the electronic gear so that the number of servo motor encoder pulses for one 
servo motor revolution is converted to the resolution of the load-side encoder. 
This parameter is not available with MR-J4W2-0303B6 servo amplifiers. 

1 

1 to  

65535 

Each 

PE05 

**FBD 

Fully closed loop control - Feedback pulse electronic gear 1 - Denominator 
Set a denominator of electronic gear for the servo motor encoder pulse at the fully 
closed loop control. 
Set the electronic gear so that the number of servo motor encoder pulses for one 
servo motor revolution is converted to the resolution of the load-side encoder. 
This parameter is not available with MR-J4W2-0303B6 servo amplifiers. 

1 

1 to  

65535 

Each 

PE06 

BC1 

Fully closed loop control - Speed deviation error detection level 
Set [AL. 42.9 Fully closed loop control error by speed deviation] of. 
When the speed deviation between the servo motor encoder and load-side encoder 
becomes larger than the setting value, the alarm will occur. 
This parameter is not available with MR-J4W2-0303B6 servo amplifiers. 

400 

[r/min] 

1 to  

50000 

Each 

 

Summary of Contents for MR-J4W2































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2

Tabor Electronics 9100A User Manual preview
9100A
Brand: Tabor Electronics Pages: 48
GAI-Tronics SP2 Instruction Manual preview
SP2
Brand: GAI-Tronics Pages: 24
JBL PX300.4 Service Manual preview
PX300.4
Brand: JBL Pages: 27
Samson MXS 2800 Owner'S Manual preview
MXS 2800
Brand: Samson Pages: 56
NAD D 7050 Quick Setup Manual preview
D 7050
Brand: NAD Pages: 2
Genie HDMID04 Quick Start Manual preview
HDMID04
Brand: Genie Pages: 5
McIntosh C1100C Connection Diagrams preview
C1100C
Brand: McIntosh Pages: 2
Target Audio TDA 270 Instruction Manual preview
TDA 270
Brand: Target Audio Pages: 16
BMC Phono MCCI Owner'S Manual preview
Phono MCCI
Brand: BMC Pages: 20
Kramer TOOLS VP-200N User Manual preview
TOOLS VP-200N
Brand: Kramer Pages: 12
B2 Audio SLD5K Owner'S Manual preview
SLD5K
Brand: B2 Audio Pages: 12
Carr Amplifiers Raleigh Owner'S Manual preview
Raleigh
Brand: Carr Amplifiers Pages: 8
Avatar AST-3004 Owner'S Manual preview
AST-3004
Brand: Avatar Pages: 16
Sams DAA-106 User Manual For Use And Maintenance preview
DAA-106
Brand: Sams Pages: 18
Sonic Farm 2di4 User Manual preview
2di4
Brand: Sonic Farm Pages: 8
Decware SE84UFO3 Owner'S Manual preview
SE84UFO3
Brand: Decware Pages: 18
B&K FIVE OR SEVEN CHANNEL 125.5 S2 User Manual preview
FIVE OR SEVEN CHANNEL 125.5 S2
Brand: B&K Pages: 12
Ma Audio M300XE Operating Instructions Manual preview
M300XE
Brand: Ma Audio Pages: 23

Brands by name

Popular brands

Load more brands