Mitsubishi Electric MR-J4W2 Instruction Manual Download | Manualshive

Page: 361 / 542

background image

16. FULLY CLOSED LOOP SYSTEM

16 - 14

16.3.2 Home position return

(1) General instruction

Home position return is all performed according to the load-side encoder feedback data, independently
of the load-side encoder type. It is irrelevant to the Z-phase position of the servo motor encoder. In the
case of a home position return using a dog signal, the home position (reference mark) must be passed
through when an incremental type linear encoder is used, or the Z-phase be passed through when a
rotary encoder is used, during a period from a home position return start until the dog signal turns off.

(2) Load-side encoder types and home position return methods

(a) About proximity dog type home position return using absolute type linear encoder

When an absolute type linear encoder is used, the home position reference position is the position
per servo motor revolution to the linear encoder home position (absolute position data = 0).
In the case of a proximity dog type home position return, the nearest position after proximity dog off
is the home position.
The linear encoder home position may be set in any position.

Linear encoder home position

Home position

Home position return speed

Creep speed

Home position return direction

ON
OFF

Proximity dog

signal

Servo motor

speed

Reference home

position

Machine position

0 r/min

Equivalent to one servo motor revolution

«
...
359
360
361
362
363
...
»

Summary of Contents for MR-J4W2































































































































































































































































































































































































































































































































































Reviews:

No comments

Related manuals for MR-J4W2

Brand: NAD Pages: 2

Brand: Aaron Pages: 2

Brand: Atlona Pages: 10

Brand: Rockford Fosgate Pages: 40

Brand: Synaestec Audio Pages: 10

Brand: Nobsound Pages: 2

Brand: Bose Pages: 75

Brand: Jas Audio Pages: 5

Lightstar Direct

Brand: Carver Pages: 20

Brand: Takstar Pages: 2

Brand: M-system Pages: 4

Brand: DaytonAudio Pages: 31

Brand: Sams Pages: 18

Brand: AMC Pages: 20

Brand: Russound Pages: 8

Brand: Phoenix Gold Pages: 8

Brand: Baudcom Pages: 16

Brand: Key Digital Pages: 11

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands