6
7
When in trouble
Before Use
Operation
Cleaning
When in trouble
Before Use
Operation
Cleaning
Install the refrigerator at:
A place with good ventilation not
exposed to direct sunlight or hot air
To prevent a diminishing in cooling
performance and to reduce power costs.
A place with low humidity
To prevent rusting, electric shock and fire.
A strong and level place
To prevent vibration and noise, and ajar
or tilting doors.
If the refrigerator supports sink easily into the floor
material, lay a strong plate or board underneath.
(To prevent deformation or discoloration
due to the weight or heat.)
A place away from other devices
To prevent noise or video interference
with devices such as televisions.
A place with at least 3 cm of
space beside the left and right of
the refrigerator, 10 cm of space from
the top and 6 cm from the back.
To allow heat to dissipate from the sides,
top and the back of the refrigerator.
Use a dedicated outlet
Use a dedicated outlet for the power supply that meets the rating specified
on the rating label. (The rating label is located on the door-liner of the
refrigerator compartment.)
The refrigerator will not be damaged even if the power
is supplied soon after installation.
It takes a while for the refrigerator to cool, therefore
supply power as soon as possible.
Electrical Connections
Make sure this unit is properly grounded.
The refrigerator should always be plugged into its dedicated electrical outlet.
This will provide the best performance and prevent electrical circuits
from being overloaded and causing a fire.
Make sure that the electrical outlet provides the proper voltage.
Extension cords are not recommended.
If your refrigerator is installed in the high humidity location, not only
ground connection but also installation of the earth leakage breaker is
recommended.
If the power cord is damaged, purchase a new cord from
MITSUBISHI ELECTRIC SERVICE CENTRE.
Make sure that the power cord is designed for this model.
A qualified service person should only replace the power cord.
Preventing ajar doors
Adjusting a tilted door or unevenness
If the door is still tilted after adjustment of the supports
Installing the support cover
While the freezer door is open
Insert the support cover horizontally
and fully, until it makes contact with
the rear side.
Installation
1
The outside of the refrigerator and the
rotating partition get hot.
Cooling takes time after turning
on the refrigerator.
Support cover
The support cover is stored inside
the refrigerator compartment
at shipment.
Connect the power supply
*Connect power supply soon after installing the refrigerator
4
2
Warning
Using outlets that do not meet the specified rating
or plugging in too many leads into a single socket
can cause heat buildup or fire.
Adjustment and anchoring
Turn the adjustable supports until they touch the floor and
the front casters are raised from the floor.
3
Adjust the supports to
make the refrigerator
level.
If the front of the
refrigerator is slightly
raised, the doors are
easier to close.
When installing the refrigerator in the corner of a room, one
of the rear supports may sink, causing the refrigerator to tilt.
If this happens, use a caster support or strong board for
adjustment.
(Normally, use a board with a thickness of about 2 to 3 mm.)
Readjust the adjustable supports as
shown in the figures below.
The right door tilts down
Raise the right side
Right Left
The left door tilts down
Support cover
The support covers are designed for the
left and right adjustable supports respectively.
Adjustable
support
Raise the left side
Rear support
Caster support or
strong board
If the installation
location is not level or
the supports sink after
a few days due to the
weight of the food,
the doors may appear
tilted.
Readjust the supports.
Rotating
partition
!"#$%&"'(&%)"&*+",+-,%.+,$&/,"*$0"-'))1"2//)+3"4+-/,+"0&/,%(."
non-cooled food or ice cream.
!"5/"(/&"/6+("&*+"3//,0"7/,+"&*$("(+2+00$,18"$(3"2)/0+"
them as soon as possible.
Adjustable
support
Flat-blade
screwdriver
Caster
Insert the blade of the screwdriver
Turn the adjustable supports
in the arrow direction until
they touch the floor.
Support cover
(To prevent vibration, noise, movement, and ajar doors)
Bottom front of refrigerator
In the summer, it may take more than 24 hours.
Heat radiation causes
the temperature to rise to
about 50
o
C to 60
o
C when
operation is first started,
and during the summer. The
rotating partition may get hot
when heated by the heater.
When making ice for the first time
A gap of
at least 10 cm
A gap of
at least 6 cm
Dedicated
outlet that meets
the specified rating.
A gap of
at least 3 cm
Turn on the power of the
refrigerator as soon as
possible.
The refrigerator will not be
damaged even if you turn on
the power immediately after
the installation.
If the supports are not
adjusted properly, the
refrigerator may move
and cause injury.
Caution
Prepare for earthquakes.
(for earthquake prone areas)
Strong belts
Warning
Thread 2 strong belts through the hand-holds on the top rear of the
refrigerator and anchor them to a strong location, such as wall or post.
To obtain the refrigerator tipping prevention belts.
The refrigerator may tip
over and cause injury.
From Installation
to Operation
Warning
5/"(/&"/40&,'2&"&*+",+-,%.+,$&/,"9+(&0
or the space around the refrigerator.
If refrigerant leaks, it may accumulate
and catch fire or explode.
Corrosion control treatment may be
required for the refrigerant circuit (pipe)
due to generation of corrosive gases.
Contact the retail store where you
purchased the refrigerator.
Use in hot spring areas
The operation noise gets
louder immediately after
installation.
Immediately after instillation, when:
the weather is hot, the doors are
frequently opened or closed, or
any similar situation; the operation
noise will get louder because the
refrigerator will switch to high-speed
operation to cool with high power.
Although R600a refrigerants are combustible, the refrigerant
circuit is hermetically sealed and normally leaks will not occur.
Warning
Should the refrigerant circuit be damaged:
1. Do not use flames or electrical appliances nearby.
2. Open the windows to fully ventilate the room.
Then, contact the retail store where you purchased the refrigerator.
Do not damage the refrigerant
circuit (pipes) or drive screws into it.
Warning
If you notice a gas leak,
do not touch the refrigerator.
Open windows to ventilate.
Ventilate
Sparks from an electrical contact
may cause an explosion or fire.
