background image

27

GB

3

Retrieving malfunction histories

• The most recent error code will be displayed sequentially whenever the 

 external timer switch is

pressed. (A maximum of 10 errors can be displayed.)

4

Resetting the malfunction history

• Press the 

 operation mode switch twice to reset all of the malfunction history information

stored within the remote controller.

NOTE: The error codes stored in the indoor units will not be reset.

5

Canceling malfunction history monitoring

• Observe the following procedure to cancel malfunction history monitoring and switch back to group

operation setting screen that was displayed prior to the self-diagnosis screen being called out.

(1)

Press the CHECK switch twice.

(2)

Press the 

 and 

 GROUP select switch.

(3)

Close the upper panel.

(4)

Press the collective ON/OFF or 

ON/OFF

 switch.

• Operations for the air-conditioner will be stopped when malfunction history monitoring is canceled in

accordance with the procedure outlined in (4). Also, if malfunction history monitoring was canceled by
pressing the collective ON/OFF switch, the screen will switch across to the collective operation setting
screen.

9. Specifications

Specifications for this equipment

Item

Details

Power supply:

DC30V (power supplied from the outdoor unit or a power unit for
transmission lines (model: PAC-SC34KUA))

Electricity consumption:

1W

Environmental conditions

Temperature 0 to 40 

°

C, humidity 30 to 90% RH

for usage:

(with no condensation)

Weight:

0.2kg

External dimensions
(H 

×

 W 

×

 D):

120 

×

 130 

×

 18 (mm)

Summary of Contents for PAC-SC30GRA




































Reviews: