background image

© 2017 Mitsubishi Electric US, Inc. 

2

2. Safety Instructions

  • This installation manual contains important safety information. 
  •  Read all Safety Instructions before using this wireless sensor.
  •  Be sure to comply with the instructions.
  •  Mitsubishi Electric components or other designated components must be used 

for installation and proper operation.

  •  This device is meant for indoor use only.

 

 This device complies with part 15 of the FCC Rules.  Operation is subject to the 

following two conditions:

          (1) This device may not cause harmful interference; and

          (2) This device must accept any interference received, including interference   

                that may cause undesired operation 

3. Notes

 • Use of the this device implies acceptance of our terms and conditions located at 

kumocloud.com/terms

.

 • Visit 

kumocloud.com/resources

 for additional information about setting up and 

controlling this device from your web browser or mobile device.

 • This equipment has been tested and found to comply with the limits for a Class 

B digital device, pursuant to Part 15 of the FCC rules. These limits are designed 

to provide reasonable protection against harmful interference in a residential 

installation.  

 • This equipment generates, uses and can radiate radio frequency energy 

and, if not installed and used in accordance with the instructions, may cause 

harmful interference to radio communications.  However, there is no guarantee 

that interference will not occur in a particular installation.  If this equipment 

does cause harmful interference to radio or television reception, which can be 

determined by turning the equipment off and on, the user is encouraged to try to 

correct the interference by one or more of the following measures:

          - Reorient or relocate the receiving antenna.

          - Increase the separation between the equipment and the receiver.

          - Connect the equipment into an outlet on a circuit different from that to which       

            the receiver is connected.

          - Consult the dealer or an experienced radio/TV technician for help.
 • This equipment complies with radio frequency exposure limits set forth by the 

FCC for an uncontrolled environment.  This equipment should be installed and 

operated with a minimum distance of 20 cm, 7.8 inches between the device and 

the user or bystanders.

  •  Changes or modifications not expressly approved by the party responsible for 

compliance could void the user’s authority to operate the equipment.

Summary of Contents for PAC-USWHS003-TH-1









Reviews: