4
(2) Wind speed and wind direction adjustment and fan operation
When you want to change the wind direction
■
While the air conditioner is operating, press the [Airflow] button
6
.
• Each time the button is pressed, the setting changes as shown be-
low.
The wind direction is displayed at
6
.
• The following wind directions can be selected:
- Depending on the indoor unit and fan model, the indoor unit may operate even when only the fan was operated.
- When “NOT AVAILABLE” is displayed when the [Ventilation] button
7
was pressed, the fan is not interlocked.
- In cases such as the following, the liquid crystal display and unit wind
speed are different:
1. When “HEAT STAND BY” or “DEFROSTING” is displayed.
2. Immediately after heating operation (while waiting for mode selec-
tion)
3. When the room temperature is higher than the set temperature in the
heating mode.
4. Dry operation
- For 3-speed models, a central controller wind speed display and the
remote controller wind speed display may be different.
NOTES
When you want to change the wind speed
■
While the air conditioner is operating, press the [Wind speed] button
5
.
• Each time the button is pressed, the setting changes as shown be-
low.
The wind speed is displayed at
5
.
• The following wind speeds can be selected:
Wind speed
4-speed model
3-speed model
2-speed model
Remote controller display
* The wind speeds that can be selected depend on the model.
- In cases such as the following, the liquid crystal display and unit airflow
may be different.
1. When “HEAT STANDBY”or “DEFROSTING” is displayed
2. Immediately after heating operation (Waiting for mode selection)
3. When the room temperature is higher than the set temperature in
the HEAT mode
NOTE
* After one hour, automatically returns to the horizontal position.
* During swing operation, remote controller display and airflow vane po-
sition cannot be synchronized.
* There may not be an airflow function, depending on the model.
(3) How to operate the timer
There are the following three timer modes. Select one of them.
1) 1 day timer mode
In this mode, the ON and OFF timers (10-minute units) can each be set to one time within 24 hours.
This mode has the following three setting methods:
· ON timer operation
: Timer only starts the air conditioner.
· OFF timer operation
: Timer only stops the air conditioner.
· ON/OFF timer operation: Timer both starts and stops the air conditioner.
2) Daily timer mode
Operation of this mode is the same as that of the 1 day timer mode. However, timer operation can be set to the same time each day in accordance
with the set ON/OFF timer time. (ON/OFF timer each 1 time/daily)
3) Auto off timer mode
The OFF timer can be easily set in 30-minute units. (30 minutes to 4 hours range) When the remaining time reaches 0:00, the air conditioner stops.
When the Auto off timer mode is selected, the next time the air conditioner is started, the OFF timer operates automatically so that the timer can be
used to turn off the air conditioner if you should forget.
When ON/OFF operation from the central controller, etc. was restricted when timer operation was set, the set ON/OFF timer is not executed. After the
restriction is removed, timer operation is performed at the ON/OFF time.
When ON/OFF operation was restricted during AUTO OFF timer operation, the remaining time at the point operation was restricted is memorized and the
air conditioner is stopped after the memorized remaining time from the time the restriction was removed.
NOTE
Setting 4
(horizontal 85˚)
Swing
Setting 1
(horizontal 0˚)
Setting 2
(horizontal 45˚)
Setting 3
(horizontal 60˚)
Display
Cool
Heat/fan
Dry
Not
settable
Airflow setting
when operation
mode was changed
Downward
85˚
Swing
Swing
* Horizontal after 1 hour
Cool
Dry
Fan
operation
Heating
operation
–
–
–
Downward
60˚
Downward
45˚
Horizontal
outlet
Downward 85˚
Downward 60˚
Downward 45˚
Horizontal outlet
Operation
mode
Wind
Speed
Fan operation
<When operating fan interlocked with indoor unit>
When the indoor unit is operated, the fan is automatically operated also.
Fan operation is displayed at
7
.
<When operating fan only while indoor unit stopped>
■
While the air conditioner is stopped, press the [Ventilation] button
7
.
The ON/OFF lamp
1
lights and fan operation is displayed at
7
.
<When you want to change the fan wind speed>
■
Press the [Ventilation] button
7
.
Each time the button is pressed, the wind speed is changed as shown
below.
(Low)
(Mid1)
(Mid2)
(High)
(Mid1)
(Mid2)
(High)
(Mid1)
(High)
High/Mid1
Mid2/Low
High
Mid1/Mid2/Low
Off
(no display)
Remote controller display
NOTES
