[16] - 10
12.Bobbin winding
Function Unit
Setting
range
Specification
W
Bobbin winding speed setting
rpm LOW
~
HIGH
Sets the speed of the sewing machine during bobbin winding.
Sets the operation of the winder
- NO
While the operation signal SRT is turned [ON], the sewing machine
rotates. When the signal is turned [OFF], the sewing machine stops.
AL
When start signal SRT is turned ON, the sewing machine continues its
operation. Furthermore, when the start signal SRT is ON, machine is
stopped.
WSM
Bobbin winding operation
setting
T
When the operation signal SRT is turned [ON], the sewing machine
continues to run within the time which is set in (WT.) function.
WT
Bobbin winding operation time
s
1 ~ 500
The bobbin winding operation time (timer) can be set.
(effective when WSM =[T])
13.Feed method
Function Unit
Setting
range
Specification
Sets the feeding method corresponding to the clamp weight. If the unusual clamp is adapted,
please set the value corresponding to the clamp weight.
- L
For standard delivery clamp [L]
M
Heavy weight setting [M]
WET
Clamp weight selection
H
Heavy weight setting [H]
WEL
Setting value when clamp
[L] is selected
%
1 ~ 100
SET value is applied when CLAMP WEIGHT SELECTION
(WET.)=[L].
It limits maximum sewing speed of each stitch length.
WEM
Setting value when clamp
[M] is selected
%
1 ~ 100
SET value is applied when CLAMP WEIGHT SELECTION
(WET.)=[M].
It limits maximum sewing speed of each stitch length.
WEH
Setting value when clamp
[H] is selected
%
1 ~ 100
SET value is applied when CLAMP WEIGHT SELECTION
(WET.)=[H].
It limits maximum sewing speed of each stitch length.
Table feed timing corresponding to the sewing material thickness can be selected. Set value
according to the sewing material thickness. The number in the () indicates the approximate
thickness.
- L
Standard setting [L]----------(0-3mm)
M
Thick material setting [M]---(3-6mm)
THI
Cloth thickness selection
H
Thick material setting [H]---(6-8mm)
TL
Setting value when cloth
thickness [L] is selected
%
1 ~ 100
SET value is applied when material THICKNESS
SELECTION(THI.)=[L]. It limits maximum sewing speed of each
stitch length. The factory setting is for approx (0 to 3mm).
TM
Setting value when cloth
thickness [M] is selected
%
1 ~ 100
SET value is applied when material THICKNESS
SELECTION(THI.)=[M]. It limits maximum sewing speed of each
stitch length. The factory setting is for approx (3 to 6mm).
TH
Setting value when cloth
thickness [H] is selected
%
1 ~ 100
SET value is applied when material THICKNESS
SELECTION(THI.)=[H]. It limits maximum sewing speed of each
stitch length. The factory setting is for approx (6 to 8mm).
The table feeding method is selected.
- ID
Table is stopped when needle point is under sewing material.
FED
Feed setting
S
Table is fed continuously even needle point is under sewing
material. (There is a risk that needle may broken depends on the
sewing material)
Non stitch feed tracks can be selected.
- K
Non stitch feed which traces the inputted tracks (slower than [S]
setting)
FEM
Setting for non stitch feed
S
Non stitch feed is moved at high speed. table moves diagonally
(45 degree) at first, then moves either X or Y direction
FSL
Non stitch feed speed
setting for long distance
-
0 ~ 9
Non stitch feed speed for long distance can be set from [0 (slow)]
to [9 (fast)].
FSS
Non stitch feed speed
setting for short distance
-
0 ~ 9
Non stitch feed speed for short distance can be set from [0
(slow)] to [9 (fast)].
TSL
Teaching speed setting for
long distance
-
0 ~ 9
Teaching speed for long distance can be set from [0 (slow)] to [9
(fast)].
Summary of Contents for PLK-G-PAL
Page 1: ...INDUSTRIAL SEWING MACHINE MODEL PLK G PAL TECHNICAL MANUAL Operation Panel A180E606P12 ...
Page 2: ......
Page 199: ...MEMO ...
Page 200: ......
