Mitsubishi Electric SE1 User Manual Download

Page: 18 / 22

Others

Remove the lamp cover.

Loosen the 2 screws, then pull up to the
direction of the arrow with your fingers on the
area shown in the figure to remove the lamp
cover.

Pull out the lamp.

Loosen the 2 screws holding the lamp in place,
and pull up the handle to remove the lamp.

Mount the new lamp.

Align the orientation, press down until the bottom is
reached, and lock in place using the two lamp
locking screws.

Replace the lamp cover.

Align the cover, and press it in, then tighten the
screws loosened in step

until the lamp cover is

no longer loose.

Reset the lamp timer.

See the lamp’s manual for instructions on resetting
the lamp timer.

Notes and Precautions

• Press the

button twice to display (a rough guide) the time of lamp use, the

Lamp time

item, in the

Status display menu

p.28

• It is recommended that the lamp should be replaced after 2,000 hours of use. When

Lamp time

reaches 2,000 hours, the

icon and a message will appear. This display

disappears when you press

button.

• Attach the lamp cover correctly so that it is not loose. If it is not attached correctly, the

lamp may fail to come on

p.35

, and the lamp’s lifetime may be shortened.

• Always replace the lamp with a new one.
• The lamp is made out of glass. Do not touch the glass surface with your bare hands,

bang it, or scratch it. (Dirt, jolts, scratches and the like could break the lamp.)

Used Lamps

This projector’s lamps contain trace amounts of environmentally harmful inorganic
mercury. Be careful not to break used lamps, and dispose it in accordance with local
regulations.

Lamp replacement (Continued)

The indicator lights inform you of internal abnormalities.

No power

⇒

Problem with projector
• Unplug the AC power cord, and contact your dealer.

Lamp went out during use, or won’t come on

⇒

Lamp temperature is high so that it is difficult to turn on, the lifetime of
the lamp has ended or the projector is malfunctioning.
• Unplug the AC power cord and wait for a short while, then turn the

power back on.

• If a lamp burns out, replace it with a new one.

❈

After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.

Power went out during use

⇒

Internal overheating, or the outside temperature is too high.
• Place the projector so that the air intake and exhaust are not blocked.
• Unplug the AC power cord and wait for a short while, then turn the

power back on.

• Clean the air filter.

p.32

❈

The

icon will appear before the power goes out.

❈

After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.

Power went out during use

⇒

Problem with internal cooling fan.
• Unplug the AC power cord, and contact your dealer.

❈

The

icon will appear before the power goes out.

❈

After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.

Power went out during use, or power won’t come on

⇒

The lamp cover is not properly attached.
• Unplug the AC power cord, and reattach the lamp cover.

p.34

❈

After approx. one minute of abnormal display, the projector returns to
the standby state waiting for internal cool down.

PRECAUTIONS

• Make sure to unplug the AC power cord if something goes wrong.
• If the AC power cord is unplugged before cooling is complete, give the lamp enough time

to cool before plugging it back in. If the lamp overheats, it may fail to light. Unplugging the
AC power cord repeatedly when the temperature is high will shorten the life of the lamp.
(Even if you are not concerned about lamp lifetime, the light may not come on if you do
not wait at least 3 minutes.)

(Off)

(Red lit) (Red lit)

Or
(Green lit)

(Green lit) (Red lit)

(Red lit)

(Off)

Or
(Orange lit)

Or
(Orange lit or flashing)

(Red lit or flashing)

(Red lit)

(Orange
flashing)

(Red lit)